WiFi 运动,心跳,跌倒监测 (一)

(参考文献:Wi-Fi Can Do More: Toward Ubiquitous Wireless Sensing. IEEE Commun. Stand. Mag. 6(2)
: 42-49 (2022))

WiFi作为最大的基础网络架构,遍布于大大小小的家庭。传统WiFi主要应用于communication以及networking功能,而现在增加了一个新的属性sensing,并构建世界最大的"sensorless" sensing network。目前,最新修订IEEE 802.11bf协议正是为WiFi sensing建立标准,预期于2024年公布。并且不仅仅是WiFi,其他如UWB,毫米波,都在未来成为研究sensing方向重要的手段。

使用WiFi做sensing所面临的的三个挑战:

  1. Wi-Fi transceivers are not synchronized, and therefore the measured channel information contains significant phase distortions.
  2. Commercial Wi-Fi has limited channel bandwidths (20MHz–80MHz).
  3. Only a small number of antennas (e.g., typically one to three on IoT devices), producing poor spatial resolution to differentiate multipath signals arriving from different angles. 
  4. How do we deploy Wi-Fi sensing solutions by integrating on top of commodity devices without affecting the primary networking functionality?

针对以上挑战的结论是:

  1. While there is a considerable number of multipaths in the complex indoor environments, the multipath resolvability of Wi-Fi signals is greatly and fundamentally constrained, making traditional two-ray reflection models and phased array signal processing techniques impractical for Wi-Fi sensing.
  2. Purely software-based solutions running on top of legacy Wi-Fi devices, which will then serve both networking and sensing concurrently, a true integrated communication and sensing solution.

基于以上作者不再采用原来的two-ray model,而是基于电磁波原理提出了一种新的方法,新方法利用尽可能所有多径并进行统计分析。采用了channel state information (CSI)+ auto-correlation function (ACF)来进行特征提取(往后的文章用了同样的方法)。具体可以实现以下功能:

  1.  Motion. (参考论文 widetect)
  2.  Periodicity (breathing rate). (参考论文 Smars) a predominantly periodic chest movement.
  3.  Speed. (参考论文 wispeed 和 gaitway)

以下是几个APP和WEB端界面,Origin Tracking (the world’s first indoor tracking
technology with centimeter accuracy even underNLoS conditions)以及HEX

 

  • 1
    点赞
  • 5
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
根据提供的引用内容,可以得知行人跌倒监测系统主要包括三个模块:检测摔倒模块、GPS定位模块和通信模块。其中,检测摔倒模块采用了MPU6050陀螺仪检测,当检测到老人摔倒之后,会通过SIM800C发送短信到紧急联系人,设备上的蜂鸣器会发出警报声,周围行人听到也可以进行帮助;并且会将GPS数据上传到云端,通过地图显示老人的位置,家人通过短信知道老人摔倒后,通过云端地图显示的位置,可以快速赶到老人身边,或者报警求助,报告位置。 因此,如果要实现行人跌倒监测系统,可以考虑使用STM32作为主控芯片,通过连接MPU6050陀螺仪模块来检测行人是否摔倒。当检测到行人摔倒后,可以通过SIM800C模块发送短信到紧急联系人,并且通过蜂鸣器发出警报声。同时,可以通过GPS模块获取行人的位置信息,并将其上传到云端,通过地图显示行人的位置,方便家人或者其他人员前来救援。 以下是可能的实现步骤: 1. 硬件准备:STM32主控芯片、MPU6050陀螺仪模块、SIM800C模块、GPS模块、蜂鸣器等。 2. 连接硬件:将MPU6050陀螺仪模块、SIM800C模块、GPS模块、蜂鸣器等连接到STM32主控芯片上。 3. 编写程序:使用STM32的开发工具,编写程序实现MPU6050陀螺仪模块的数据读取和分析,当检测到行人摔倒时,通过SIM800C模块发送短信到紧急联系人,并且通过蜂鸣器发出警报声。同时,通过GPS模块获取行人的位置信息,并将其上传到云端。 4. 测试和调试:将系统进行测试和调试,确保系统能够正常工作。

“相关推荐”对你有帮助么?

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值