FPGA小白学习之路（2）error:buffers of the same direction cannot be placed in series

最新推荐文章于 2023-06-29 17:56:55 发布

weixin_30361753

最新推荐文章于 2023-06-29 17:56:55 发布

阅读量529

点赞数 1

文章标签：前端 ViewUI

原文链接：http://www.cnblogs.com/kybyano/p/8179830.html

版权

锁相环PLL默认输入前端有个IBUFG单元,在输出端有个BUFG单元,而两个BUFG（IBUFG）不能相连,所以会报这样的错:

ERROR:NgdBuild:770 - IBUFG 'u_pll0/clkin1_buf' and BUFG 'BUFG_inst' on net

'clkin_w' are lined up in series. Buffers of the same direction cannot be

placed in series.

ERROR:NgdBuild:924 - input pad net 'clkin_w' is driving non-buffer primitives:

如下示例代码：

[Demo1]

 1 // demo1 two bufg connect
 2 
 3 module iobuf(
 4 
 5  　　input 　　clk,
 6 
 7 　　 input 　　rst,
 8 
 9  　　output　　led
10 
11  　　);
12 
13  wire clkin_w;
14 
15  BUFG BUFG_inst(
16 
17       .O(clkin_w),           // Clock buffer output
18 
19       .I(clk)                   // Clock buffer input
20 
21    　　);
22 
23  pll0 u_pll0(
24 
25     　　.CLK_IN1(clkin_w),      // IN
26 
27     　　.CLK_OUT1(clkout),  // OUT
28 
29     　　.RESET(rst));       // IN
30 
31 assign led = clkout;
32 
33 endmodule

普通IO不能直接做锁相环的输入,所以会报这样的错:

ERROR:Place:1397 - A clock IOB / MMCM clock component pair have been found that

are not placed at an optimal clock IOB / MMCM site pair. The clock IOB

component <clk> is placed at site <A18>. The corresponding MMCM component

<u_pll0/mmcm_adv_inst> is placed at site <MMCME2_ADV_X0Y0>. The clock IO can

use the fast path between the IOB and the MMCM if the IOB is placed on a

Clock Capable IOB site that has dedicated fast path to MMCM sites within the

same clock region. You may want to analyze why this problem exists and

correct it. If this sub optimal condition is acceptable for this design, you

may use the CLOCK_DEDICATED_ROUTE constraint in the .ucf file to demote this

message to a WARNING and allow your design to continue. However, the use of

this override is highly discouraged as it may lead to very poor timing

results. It is recommended that this error condition be corrected in the

design. A list of all the COMP.PINs used in this clock placement rule is

ERROR:Pack:1654 - The timing-driven placement phase encountered an error.

如果有ucf中加上这句约束:

1 NET clk          CLOCK_DEDICATED_ROUTE = FALSE;

依旧会报错,在ZYNQ7000系列,这样还是通不过,如下:

ERROR:PhysDesignRules:2256 - Unsupported MMCME2_ADV configuration. The signal

u_pll0/clkin1 on the CLKIN1 pin of MMCME2_ADV comp u_pll0/mmcm_adv_inst with

COMPENSATION mode ZHOLD must be driven by a clock capable IOB.

ERROR:Pack:1642 - Errors in physical DRC.

如下示例代码

[Demo2]

 1 // demo2 regular io directly connect to PLL
 2 
 3 module iobuf(
 4 
 5     input clk,
 6 
 7  　　input     rst,
 8 
 9  　　output   led
10 
11  );
12   
13 
14 
15  pll0 u_pll0(
16 
17     .CLK_IN1(clk),      // IN
18 
19     .CLK_OUT1(clkout),  // OUT
20 
21     .RESET(rst));       // IN
22 
23 assign led = clkout;
24 
25 endmodule

使用普通的IO,再连接bufg来连到时钟线上,

仍会报这样的错误,因为还是两bufg相连了:

ERROR:NgdBuild:770 - IBUFG 'u_pll0/clkin1_buf' and BUFG 'BUFG_inst' on net

'clkin_w' are lined up in series. Buffers of the same direction cannot be

placed in series.

ERROR:NgdBuild:924 - input pad net 'clkin_w' is driving non-buffer primitives:

修改为如下：

[Demo3]

 1 // dem3 regular io with BUFG then connect to PLL which with"No Buffer" setting
 2 
 3  module iobuf(
 4 
 5  　　input　　clk,
 6 
 7  　　input　　rst,
 8 
 9  　　output　　led
10 
11  　　);
12 
13  wire clkin_w;
14 
15  BUFG BUFG_inst (
16 
17       .O(clkin_w),           // Clock buffer output
18 
19       .I(clk)                   // Clock buffer input
20 
21    );
22 
23  pll0 u_pll0(
24 
25     .CLK_IN1(clkin_w),      // IN
26 
27     .CLK_OUT1(clkout),  // OUT
28 
29     .RESET(rst));       // IN
30 
31 assign led = clkout;
32 
33 endmodule