modbus接口的温湿度slave设备

最新推荐文章于 2024-04-16 08:38:46 发布
最新推荐文章于 2024-04-16 08:38:46 发布
阅读量134 收藏
点赞数
文章标签： 单片机 stm32 物联网
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/weixin_51688234/article/details/128684300
版权

一、STM32移植RT_THread

1.CubeMX安装Nano pack

先获取软件包地址：https://www.rt-thread.org/download/cube/RealThread.RT-Thread.pdsc
打开 CubeMX，从菜单栏 help 进入 Manage embedded software packages 界面，点击 From Url 按钮，进入 User Defined Packs Manager 界面，其次点击 new，填入上述网址，然后点击 check

2.keil MDK安装RT_THread

CubeMX新建文件

选择 Nano 组件
（1）点击 Softwares Packages->Select Components，进入组件配置界面，选择 RealThread， 然后根3.1.5版本的，然后点击 OK 按钮
这时会新增Software Packs展开就可以看见添加的RealThread.RT_Thread,勾选相应内容
请添加图片描述

RCC配置
请添加图片描述
SYS配置
请添加图片描述
设置NVIC
请添加图片描述

GPIO选择b15串口，用来点亮LED灯
请添加图片描述

设置TIM3
请添加图片描述

时钟树配置
请添加图片描述

生成项目
请添加图片描述

请添加图片描述

二、Keil代码编写

1.添加AHT文件

请添加图片描述

将AHT添加到项目中、
请添加图片描述

请添加图片描述

修改AHT20-21_DEMO_V1_3.c

/*******************************************/
/*@????:??????????          */
/*@??:?????????                */
/*@??:V1.2                              */
/*******************************************/
//#include "main.h" 
#include "AHT20.h" 
#include "gpio.h"
#include "i2c.h"


void Delay_N10us(uint32_t t)//????
{
  uint32_t k;

   while(t--)
  {
    for (k = 0; k < 2; k++);//110
  }
}

void SensorDelay_us(uint32_t t)//????
{
		
	for(t = t-2; t>0; t--)
	{
		Delay_N10us(1);
	}
}

void Delay_4us(void)		//????
{	
	Delay_N10us(1);
	Delay_N10us(1);
	Delay_N10us(1);
	Delay_N10us(1);
}
void Delay_5us(void)		//????
{	
	Delay_N10us(1);
	Delay_N10us(1);
	Delay_N10us(1);
	Delay_N10us(1);
	Delay_N10us(1);

}

void Delay_1ms(uint32_t t)		//????
{
   while(t--)
  {
    SensorDelay_us(1000);//??1ms
  }
}


//void AHT20_Clock_Init(void)		//????
//{
//	RCC_APB2PeriphClockCmd(CC_APB2Periph_GPIOB,ENABLE);
//}

void SDA_Pin_Output_High(void)   //?PB7????? , ???????, PB7??I2C?SDA
{
	GPIO_InitTypeDef  GPIO_InitStruct;
	GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;//????
	GPIO_InitStruct.Pin = GPIO_PIN_7;
	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
	HAL_GPIO_Init(GPIOB,& GPIO_InitStruct);
	HAL_GPIO_WritePin(GPIOB,GPIO_PIN_7,GPIO_PIN_SET);
}

void SDA_Pin_Output_Low(void)  //?P7?????  ???????
{
	GPIO_InitTypeDef  GPIO_InitStruct;
	GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;//????
	GPIO_InitStruct.Pin = GPIO_PIN_7;
	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
	HAL_GPIO_Init(GPIOB,& GPIO_InitStruct);
	HAL_GPIO_WritePin(GPIOB,GPIO_PIN_7,GPIO_PIN_RESET);
}

void SDA_Pin_IN_FLOATING(void)  //SDA???????
{
	GPIO_InitTypeDef  GPIO_InitStruct;
	GPIO_InitStruct.Mode = GPIO_MODE_INPUT;//??
	GPIO_InitStruct.Pin = GPIO_PIN_7;
	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
	HAL_GPIO_Init( GPIOB,&GPIO_InitStruct);
}


void SCL_Pin_Output_High(void) //SCL?????,P14??I2C?SCL
{
	HAL_GPIO_WritePin(GPIOB,GPIO_PIN_6,GPIO_PIN_SET);
}

void SCL_Pin_Output_Low(void) //SCL?????
{
	HAL_GPIO_WritePin(GPIOB,GPIO_PIN_6,GPIO_PIN_RESET);
}

void Init_I2C_Sensor_Port(void) //???I2C??,??????
{	
	GPIO_InitTypeDef  GPIO_InitStruct;
	GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;//????
	GPIO_InitStruct.Pin = GPIO_PIN_7;
	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
	HAL_GPIO_Init(GPIOB,& GPIO_InitStruct);
	HAL_GPIO_WritePin(GPIOB,GPIO_PIN_15,GPIO_PIN_SET);

	
	GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;//????
	GPIO_InitStruct.Pin = GPIO_PIN_6;
	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
	HAL_GPIO_Init(GPIOB,& GPIO_InitStruct);
	HAL_GPIO_WritePin(GPIOB,GPIO_PIN_15,GPIO_PIN_SET);
	
}
void I2C_Start(void)		 //I2C????START??
{
	SDA_Pin_Output_High();
	SensorDelay_us(8);
	SCL_Pin_Output_High();
	SensorDelay_us(8);
	SDA_Pin_Output_Low();
	SensorDelay_us(8);
	SCL_Pin_Output_Low();
	SensorDelay_us(8);   
}


void AHT20_WR_Byte(uint8_t Byte) //?AHT20?????
{
	uint8_t Data,N,i;	
	Data=Byte;
	i = 0x80;
	for(N=0;N<8;N++)
	{
		SCL_Pin_Output_Low(); 
		Delay_4us();	
		if(i&Data)
		{
			SDA_Pin_Output_High();
		}
		else
		{
			SDA_Pin_Output_Low();
		}	
			
    SCL_Pin_Output_High();
		Delay_4us();
		Data <<= 1;
		 
	}
	SCL_Pin_Output_Low();
	SensorDelay_us(8);   
	SDA_Pin_IN_FLOATING();
	SensorDelay_us(8);	
}	


uint8_t AHT20_RD_Byte(void)//?AHT20??????
{
		uint8_t Byte,i,a;
	Byte = 0;
	SCL_Pin_Output_Low();
	
	SDA_Pin_IN_FLOATING();
	SensorDelay_us(8);	
	
	for(i=0;i<8;i++)
	{
    SCL_Pin_Output_High();
		
		Delay_5us();
		a=0;
		
		//if(GPIO_ReadInputDataBit(GPIOB,GPIO_Pin_15)) a=1;
		if(HAL_GPIO_ReadPin(GPIOB,GPIO_PIN_7)) a=1;
		Byte = (Byte<<1)|a;
		
		//SCL_Pin_Output_Low();
		HAL_GPIO_WritePin(GPIOB,GPIO_PIN_6,GPIO_PIN_RESET);
		Delay_5us();
	}
  SDA_Pin_IN_FLOATING();
	SensorDelay_us(8);	
	return Byte;
}


uint8_t Receive_ACK(void)   //?AHT20?????ACK
{
	uint16_t CNT;
	CNT = 0;
	SCL_Pin_Output_Low();	
	SDA_Pin_IN_FLOATING();
	SensorDelay_us(8);	
	SCL_Pin_Output_High();	
	SensorDelay_us(8);	
	while((HAL_GPIO_ReadPin(GPIOB,GPIO_PIN_7))  && CNT < 100) 
	CNT++;
	if(CNT == 100)
	{
		return 0;
	}
 	SCL_Pin_Output_Low();	
	SensorDelay_us(8);	
	return 1;
}

void Send_ACK(void)		  //????ACK??
{
	SCL_Pin_Output_Low();	
	SensorDelay_us(8);	
	SDA_Pin_Output_Low();
	SensorDelay_us(8);	
	SCL_Pin_Output_High();	
	SensorDelay_us(8);
	SCL_Pin_Output_Low();	
	SensorDelay_us(8);
	SDA_Pin_IN_FLOATING();
	SensorDelay_us(8);
}

void Send_NOT_ACK(void)	//?????ACK
{
	SCL_Pin_Output_Low();	
	SensorDelay_us(8);
	SDA_Pin_Output_High();
	SensorDelay_us(8);
	SCL_Pin_Output_High();	
	SensorDelay_us(8);		
	SCL_Pin_Output_Low();	
	SensorDelay_us(8);
    SDA_Pin_Output_Low();
	SensorDelay_us(8);
}

void Stop_I2C(void)	  //??????
{
	SDA_Pin_Output_Low();
	SensorDelay_us(8);
	SCL_Pin_Output_High();	
	SensorDelay_us(8);
	SDA_Pin_Output_High();
	SensorDelay_us(8);
}

uint8_t AHT20_Read_Status(void)//??AHT20??????
{

	uint8_t Byte_first;	
	I2C_Start();
	AHT20_WR_Byte(0x71);
	Receive_ACK();
	Byte_first = AHT20_RD_Byte();
	Send_NOT_ACK();
	Stop_I2C();
	return Byte_first;
}

uint8_t AHT20_Read_Cal_Enable(void)  //??cal enable??????
{
	uint8_t val = 0;//ret = 0,
  val = AHT20_Read_Status();
	 if((val & 0x68)==0x08)
		 return 1;
   else  return 0;
 }

void AHT20_SendAC(void) //?AHT20??AC??
{

	I2C_Start();
	AHT20_WR_Byte(0x70);
	Receive_ACK();
	AHT20_WR_Byte(0xac);//0xAC????
	Receive_ACK();
	AHT20_WR_Byte(0x33);
	Receive_ACK();
	AHT20_WR_Byte(0x00);
	Receive_ACK();
	Stop_I2C();

}

//CRC????:CRC8/MAXIM
//???:X8+X5+X4+1
//Poly:0011 0001  0x31
//????????? 1000 1100 0x8c
//C????:
uint8_t Calc_CRC8(uint8_t *message,uint8_t Num)
{
	uint8_t i;
	uint8_t byte;
	uint8_t crc=0xFF;
  for(byte=0; byte<Num; byte++)
  {
    crc^=(message[byte]);
    for(i=8;i>0;--i)
    {
      if(crc&0x80) crc=(crc<<1)^0x31;
      else crc=(crc<<1);
    }
  }
        return crc;
}

void AHT20_Read_CTdata(uint32_t *ct) //??CRC??,????AHT20????????
{
		volatile uint8_t  Byte_1th=0;
	volatile uint8_t  Byte_2th=0;
	volatile uint8_t  Byte_3th=0;
	volatile uint8_t  Byte_4th=0;
	volatile uint8_t  Byte_5th=0;
	volatile uint8_t  Byte_6th=0;
	 uint32_t RetuData = 0;
	uint16_t cnt = 0;
	AHT20_SendAC();//?AHT10??AC??
	Delay_1ms(80);//??80ms??	
    cnt = 0;
	while(((AHT20_Read_Status()&0x80)==0x80))//????bit[7]?0,???????,??1,?????
	{
		SensorDelay_us(1508);
		if(cnt++>=100)
		{
		 break;
		 }
	}
	I2C_Start();
	AHT20_WR_Byte(0x71);
	Receive_ACK();
	Byte_1th = AHT20_RD_Byte();//???,??????0x98,??????,bit[7]?1;???0x1C,??0x0C,??0x08???????,bit[7]?0
	Send_ACK();
	Byte_2th = AHT20_RD_Byte();//??
	Send_ACK();
	Byte_3th = AHT20_RD_Byte();//??
	Send_ACK();
	Byte_4th = AHT20_RD_Byte();//??/??
	Send_ACK();
	Byte_5th = AHT20_RD_Byte();//??
	Send_ACK();
	Byte_6th = AHT20_RD_Byte();//??
	Send_NOT_ACK();
	Stop_I2C();

	RetuData = (RetuData|Byte_2th)<<8;
	RetuData = (RetuData|Byte_3th)<<8;
	RetuData = (RetuData|Byte_4th);
	RetuData =RetuData >>4;
	ct[0] = RetuData;//??
	RetuData = 0;
	RetuData = (RetuData|Byte_4th)<<8;
	RetuData = (RetuData|Byte_5th)<<8;
	RetuData = (RetuData|Byte_6th);
	RetuData = RetuData&0xfffff;
	ct[1] =RetuData; //??

}


void AHT20_Read_CTdata_crc(uint32_t *ct) //CRC???,??AHT20????????
{
		volatile uint8_t  Byte_1th=0;
	volatile uint8_t  Byte_2th=0;
	volatile uint8_t  Byte_3th=0;
	volatile uint8_t  Byte_4th=0;
	volatile uint8_t  Byte_5th=0;
	volatile uint8_t  Byte_6th=0;
	volatile uint8_t  Byte_7th=0;
	 uint32_t RetuData = 0;
	 uint16_t cnt = 0;
	// uint8_t  CRCDATA=0;
	 uint8_t  CTDATA[6]={0};//??CRC????
	
	AHT20_SendAC();//?AHT10??AC??
	Delay_1ms(80);//??80ms??	
    cnt = 0;
	while(((AHT20_Read_Status()&0x80)==0x80))//????bit[7]?0,???????,??1,?????
	{
		SensorDelay_us(1508);
		if(cnt++>=100)
		{
		 break;
		}
	}
	
	I2C_Start();

	AHT20_WR_Byte(0x71);
	Receive_ACK();
	CTDATA[0]=Byte_1th = AHT20_RD_Byte();//???,??????0x98,??????,bit[7]?1;???0x1C,??0x0C,??0x08???????,bit[7]?0
	Send_ACK();
	CTDATA[1]=Byte_2th = AHT20_RD_Byte();//??
	Send_ACK();
	CTDATA[2]=Byte_3th = AHT20_RD_Byte();//??
	Send_ACK();
	CTDATA[3]=Byte_4th = AHT20_RD_Byte();//??/??
	Send_ACK();
	CTDATA[4]=Byte_5th = AHT20_RD_Byte();//??
	Send_ACK();
	CTDATA[5]=Byte_6th = AHT20_RD_Byte();//??
	Send_ACK();
	Byte_7th = AHT20_RD_Byte();//CRC??
	Send_NOT_ACK();                           //??: ?????NAK
	Stop_I2C();
	
	if(Calc_CRC8(CTDATA,6)==Byte_7th)
	{
	RetuData = (RetuData|Byte_2th)<<8;
	RetuData = (RetuData|Byte_3th)<<8;
	RetuData = (RetuData|Byte_4th);
	RetuData =RetuData >>4;
	ct[0] = RetuData;//??
	RetuData = 0;
	RetuData = (RetuData|Byte_4th)<<8;
	RetuData = (RetuData|Byte_5th)<<8;
	RetuData = (RetuData|Byte_6th);
	RetuData = RetuData&0xfffff;
	ct[1] =RetuData; //??
		
	}
	else
	{
		ct[0]=0x00;
		ct[1]=0x00;//???????,????????????
	}//CRC??
}


void AHT20_Init(void)   //???AHT20
{	
	Init_I2C_Sensor_Port();
	I2C_Start();
	AHT20_WR_Byte(0x70);
	Receive_ACK();
	AHT20_WR_Byte(0xa8);//0xA8??NOR????
	Receive_ACK();
	AHT20_WR_Byte(0x00);
	Receive_ACK();
	AHT20_WR_Byte(0x00);
	Receive_ACK();
	Stop_I2C();

	Delay_1ms(10);//??10ms??

	I2C_Start();
	AHT20_WR_Byte(0x70);
	Receive_ACK();
	AHT20_WR_Byte(0xbe);//0xBE?????,AHT20???????0xBE,   AHT10???????0xE1
	Receive_ACK();
	AHT20_WR_Byte(0x08);//?????bit[3]?1,?????
	Receive_ACK();
	AHT20_WR_Byte(0x00);
	Receive_ACK();
	Stop_I2C();
	Delay_1ms(10);//??10ms??
}
void JH_Reset_REG(uint8_t addr)
{
	
	uint8_t Byte_first,Byte_second,Byte_third;
	I2C_Start();
	AHT20_WR_Byte(0x70);//???0x70
	Receive_ACK();
	AHT20_WR_Byte(addr);
	Receive_ACK();
	AHT20_WR_Byte(0x00);
	Receive_ACK();
	AHT20_WR_Byte(0x00);
	Receive_ACK();
	Stop_I2C();

	Delay_1ms(5);//??5ms??
	I2C_Start();
	AHT20_WR_Byte(0x71);//
	Receive_ACK();
	Byte_first = AHT20_RD_Byte();
	Send_ACK();
	Byte_second = AHT20_RD_Byte();
	Send_ACK();
	Byte_third = AHT20_RD_Byte();
	Send_NOT_ACK();
	Stop_I2C();
	
  Delay_1ms(10);//??10ms??
	I2C_Start();
	AHT20_WR_Byte(0x70);///
	Receive_ACK();
	AHT20_WR_Byte(0xB0|addr);//?????
	Receive_ACK();
	AHT20_WR_Byte(Byte_second);
	Receive_ACK();
	AHT20_WR_Byte(Byte_third);
	Receive_ACK();
	Stop_I2C();
	
	Byte_second=0x00;
	Byte_third =0x00;
}

void AHT20_Start_Init(void)
{
	JH_Reset_REG(0x1b);
	JH_Reset_REG(0x1c);
	JH_Reset_REG(0x1e);
}

修改AHT20-21_DEMO_V1_3.h

#ifndef _AHT20_DEMO_
#define _AHT20_DEMO_

#include "main.h"  

void Delay_N10us(uint32_t t);//????
void SensorDelay_us(uint32_t t);//????
void Delay_4us(void);		//????
void Delay_5us(void);		//????
void Delay_1ms(uint32_t t);	
void AHT20_Clock_Init(void);		//????
void SDA_Pin_Output_High(void)  ; //?PB15????? , ???????, PB15??I2C?SDA
void SDA_Pin_Output_Low(void);  //?P15?????  ???????
void SDA_Pin_IN_FLOATING(void);  //SDA???????
void SCL_Pin_Output_High(void); //SCL?????,P14??I2C?SCL
void SCL_Pin_Output_Low(void); //SCL?????
void Init_I2C_Sensor_Port(void); //???I2C??,??????
void I2C_Start(void);		 //I2C????START??
void AHT20_WR_Byte(uint8_t Byte); //?AHT20?????
uint8_t AHT20_RD_Byte(void);//?AHT20??????
uint8_t Receive_ACK(void);   //?AHT20?????ACK
void Send_ACK(void)	;	  //????ACK??
void Send_NOT_ACK(void);	//?????ACK
void Stop_I2C(void);	  //??????
uint8_t AHT20_Read_Status(void);//??AHT20??????
uint8_t AHT20_Read_Cal_Enable(void);  //??cal enable??????
void AHT20_SendAC(void); //?AHT20??AC??
uint8_t Calc_CRC8(uint8_t *message,uint8_t Num);
void AHT20_Read_CTdata(uint32_t *ct); //??CRC??,????AHT20????????
void AHT20_Read_CTdata_crc(uint32_t *ct); //CRC???,??AHT20????????
void AHT20_Init(void);   //???AHT20
void JH_Reset_REG(uint8_t addr);///?????
void AHT20_Start_Init(void);///?????????????
#endif

2.移植freeModebusRTU

下载链接：https://github.com/cwalter-at/freemodbus

解压并打开刚刚下载的文件，点进demo里，新建一个STM32MB文件夹将BARE文件夹里的文件全部复制到刚刚建立的STM32MB文件夹里再把modbus文件夹全部复制到刚刚新建的STM32MB文件夹
请添加图片描述

打开项目里的MDK-ARM文件，将开始新建的STM32MB文件复制到这里
请添加图片描述

3.添加至项目

新建名为MB和MB_Port的组，MB内添加STM32MB文件夹下modbus文件夹内所有文件，MB_Port内添加STM32MB文件夹下port文件夹内所有.c文件以及根目录的demo.c文件：
请添加图片描述

请添加图片描述

请添加图片描述

4.修改代码

在Application/USER文件夹下新建app_rt_thread.c文件，并添加以下代码：

#include "rtthread.h"
#include "main.h"
#include "stdio.h"
#include "usart.h"
#include "AHT20-21_DEMO_V1_3.h" 
#include "mb.h"
#include "mbport.h"
 
struct rt_thread led1_thread;
rt_uint8_t rt_led1_thread_stack[128];
void led1_task_entry(void *parameter);
 
 
//初始化线程函数
void MX_RT_Thread_Init(void)
{
	//初始化LED1线程
	rt_thread_init(&led1_thread,"led1",led1_task_entry,RT_NULL,&rt_led1_thread_stack[0],sizeof(rt_led1_thread_stack),3,20);
	//开启线程调度
	rt_thread_startup(&led1_thread);
}
 
//主任务
void MX_RT_Thread_Process(void)
{
	( void )eMBPoll(  );//启动modbus侦听

}
 
//LED1任务
void led1_task_entry(void *parameter)
{
	while(1)
	{
		HAL_GPIO_WritePin(GPIOB,GPIO_PIN_15, GPIO_PIN_RESET);
		rt_thread_delay(500);
		HAL_GPIO_WritePin(GPIOB,GPIO_PIN_15, GPIO_PIN_SET);
		rt_thread_delay(500);
	}
}

修改Middlewares/RT-Thread/RTOS/kernel文件夹下的board.c文件，将串口USART2改为为USART1：
请添加图片描述

修改main.c文件

/* USER CODE BEGIN Header */
/**
  ******************************************************************************
  * @file           : main.c
  * @brief          : Main program body
  ******************************************************************************
  * @attention
  *
  * Copyright (c) 2022 STMicroelectronics.
  * All rights reserved.
  *
  * This software is licensed under terms that can be found in the LICENSE file
  * in the root directory of this software component.
  * If no LICENSE file comes with this software, it is provided AS-IS.
  *
  ******************************************************************************
  */
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "dma.h"
#include "i2c.h"
#include "tim.h"
#include "usart.h"
#include "gpio.h"
#include "mb.h"
#include "mbport.h"
/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
#include <stdio.h>
#include "AHT20-21_DEMO_V1_3.h" 
/* USER CODE END Includes */

/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */
extern void MX_RT_Thread_Init(void);
extern void MX_RT_Thread_Process(void);
/* USER CODE END PTD */

/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD */

/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM */

/* USER CODE END PM */

/* Private variables ---------------------------------------------------------*/

/* USER CODE BEGIN PV */

/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
/* USER CODE BEGIN PFP */

/* USER CODE END PFP */

/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

/**
  * @brief  The application entry point.
  * @retval int
  */
int main(void)
{
  /* USER CODE BEGIN 1 */
  /* USER CODE END 1 */

  /* MCU Configuration--------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* USER CODE BEGIN Init */

  /* USER CODE END Init */

  /* Configure the system clock */
  SystemClock_Config();

  /* USER CODE BEGIN SysInit */

  /* USER CODE END SysInit */

  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_DMA_Init();
  MX_I2C1_Init();
  MX_USART1_UART_Init();
  MX_TIM3_Init();
	AHT20_Init();
	eMBInit( MB_RTU, 0x01, 1, 115200, MB_PAR_NONE);//初始化modbus，走modbusRTU，从站地址为0x01，端口为1。
	eMBEnable(  );//使能modbus
  /* USER CODE BEGIN 2 */
 MX_RT_Thread_Init();
 
  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
    /* USER CODE END WHILE */
		( void )eMBPoll(  );//启动modbus侦听
    /* USER CODE BEGIN 3 */
  }
  /* USER CODE END 3 */
}

/**
  * @brief System Clock Configuration
  * @retval None
  */
void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  /** Initializes the RCC Oscillators according to the specified parameters
  * in the RCC_OscInitTypeDef structure.
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }

  /** Initializes the CPU, AHB and APB buses clocks
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
  {
    Error_Handler();
  }
}

/* USER CODE BEGIN 4 */

/* USER CODE END 4 */

/**
  * @brief  This function is executed in case of error occurrence.
  * @retval None
  */
void Error_Handler(void)
{
  /* USER CODE BEGIN Error_Handler_Debug */
  /* User can add his own implementation to report the HAL error return state */
  __disable_irq();
  while (1)
  {
  }
  /* USER CODE END Error_Handler_Debug */
}

#ifdef  USE_FULL_ASSERT
/**
  * @brief  Reports the name of the source file and the source line number
  *         where the assert_param error has occurred.
  * @param  file: pointer to the source file name
  * @param  line: assert_param error line source number
  * @retval None
  */
void assert_failed(uint8_t *file, uint32_t line)
{
  /* USER CODE BEGIN 6 */
  /* User can add his own implementation to report the file name and line number,
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
  /* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

修改 portserial.c文件：

/*
 * FreeModbus Libary: BARE Port
 * Copyright (C) 2006 Christian Walter <wolti@sil.at>
 *
 * This library is free software; you can redistribute it and/or
 * modify it under the terms of the GNU Lesser General Public
 * License as published by the Free Software Foundation; either
 * version 2.1 of the License, or (at your option) any later version.
 *
 * This library is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 * Lesser General Public License for more details.
 *
 * You should have received a copy of the GNU Lesser General Public
 * License along with this library; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
 *
 * File: $Id$
 */

#include "port.h"

/* ----------------------- Modbus includes ----------------------------------*/
#include "mb.h"
#include "mbport.h"
#include "usart.h"

/* ----------------------- static functions ---------------------------------*/
void prvvUARTTxReadyISR( void );
void prvvUARTRxISR( void );

/* ----------------------- Start implementation -----------------------------*/
void
vMBPortSerialEnable( BOOL xRxEnable, BOOL xTxEnable )
{
    /* If xRXEnable enable serial receive interrupts. If xTxENable enable
     * transmitter empty interrupts.
     */
	 if (xRxEnable)															//将串口收发中断和modbus联系起来，下面的串口改为自己使能的串口
			{
				__HAL_UART_ENABLE_IT(&huart1,UART_IT_RXNE);	//我用的是串口1，故为&huart1
			}
		else
			{
				__HAL_UART_DISABLE_IT(&huart1,UART_IT_RXNE);
			}
		if (xTxEnable)
			{
				__HAL_UART_ENABLE_IT(&huart1,UART_IT_TXE);
			}
		else
			{
				__HAL_UART_DISABLE_IT(&huart1,UART_IT_TXE);
			}	
}

BOOL
xMBPortSerialInit( UCHAR ucPORT, ULONG ulBaudRate, UCHAR ucDataBits, eMBParity eParity )
{
    return TRUE;
}

BOOL
xMBPortSerialPutByte( CHAR ucByte )
{
    /* Put a byte in the UARTs transmit buffer. This function is called
     * by the protocol stack if pxMBFrameCBTransmitterEmpty( ) has been
     * called. */
	if(HAL_UART_Transmit (&huart1 ,(uint8_t *)&ucByte,1,0x01) != HAL_OK )	//添加发送一位代码
			   return FALSE ;
			else
    return TRUE;
}

BOOL
xMBPortSerialGetByte( CHAR * pucByte )
{
    /* Return the byte in the UARTs receive buffer. This function is called
     * by the protocol stack after pxMBFrameCBByteReceived( ) has been called.
     */
	if(HAL_UART_Receive (&huart1 ,(uint8_t *)pucByte,1,0x01) != HAL_OK )//添加接收一位代码
			    return FALSE ;
	   else
    return TRUE;
}

/* Create an interrupt handler for the transmit buffer empty interrupt
 * (or an equivalent) for your target processor. This function should then
 * call pxMBFrameCBTransmitterEmpty( ) which tells the protocol stack that
 * a new character can be sent. The protocol stack will then call 
 * xMBPortSerialPutByte( ) to send the character.
 */
void prvvUARTTxReadyISR( void )
{
    pxMBFrameCBTransmitterEmpty(  );
}

/* Create an interrupt handler for the receive interrupt for your target
 * processor. This function should then call pxMBFrameCBByteReceived( ). The
 * protocol stack will then call xMBPortSerialGetByte( ) to retrieve the
 * character.
 */
void prvvUARTRxISR( void )
{
    pxMBFrameCBByteReceived(  );
}

修改porttimer.c文件：

/*
 * FreeModbus Libary: BARE Port
 * Copyright (C) 2006 Christian Walter <wolti@sil.at>
 *
 * This library is free software; you can redistribute it and/or
 * modify it under the terms of the GNU Lesser General Public
 * License as published by the Free Software Foundation; either
 * version 2.1 of the License, or (at your option) any later version.
 *
 * This library is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 * Lesser General Public License for more details.
 *
 * You should have received a copy of the GNU Lesser General Public
 * License along with this library; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
 *
 * File: $Id$
 */

/* ----------------------- Platform includes --------------------------------*/
#include "port.h"
#include "stm32f1xx_hal.h"
#include "tim.h"
/* ----------------------- Modbus includes ----------------------------------*/
#include "mb.h"
#include "mbport.h"

/* ----------------------- static functions ---------------------------------*/
void prvvTIMERExpiredISR( void );

/* ----------------------- Start implementation -----------------------------*/
BOOL
xMBPortTimersInit( USHORT usTim1Timerout50us )//定时器初始化直接返回TRUE，已经在mian函数初始化过
{
    return  TRUE;
}


inline void
vMBPortTimersEnable(  )//使能定时器中断，我用的是定时器4，所以为&htim4
{
    /* Enable the timer with the timeout passed to xMBPortTimersInit( ) */
				 /* Enable the timer with the timeout passed to xMBPortTimersInit( ) */
		__HAL_TIM_CLEAR_IT(&htim3,TIM_IT_UPDATE);
		__HAL_TIM_ENABLE_IT(&htim3,TIM_IT_UPDATE);
		__HAL_TIM_SET_COUNTER(&htim3,0);
		__HAL_TIM_ENABLE(&htim3);
}

inline void
vMBPortTimersDisable(  )//取消定时器中断
{
    /* Disable any pending timers. */
	__HAL_TIM_DISABLE(&htim3);
			__HAL_TIM_SET_COUNTER(&htim3,0);
			__HAL_TIM_DISABLE_IT(&htim3,TIM_IT_UPDATE);
			__HAL_TIM_CLEAR_IT(&htim3,TIM_IT_UPDATE);

}

/* Create an ISR which is called whenever the timer has expired. This function
 * must then call pxMBPortCBTimerExpired( ) to notify the protocol stack that
 * the timer has expired.
 */
void prvvTIMERExpiredISR( void )//modbus定时器动作，需要在中断内使用
{
    ( void )pxMBPortCBTimerExpired(  );
}

修改port.h文件：

/* USER CODE BEGIN Header */
/**
  ******************************************************************************
  * @file    stm32f1xx_it.c
  * @brief   Interrupt Service Routines.
  ******************************************************************************
  * @attention
  *
  * Copyright (c) 2022 STMicroelectronics.
  * All rights reserved.
  *
  * This software is licensed under terms that can be found in the LICENSE file
  * in the root directory of this software component.
  * If no LICENSE file comes with this software, it is provided AS-IS.
  *
  ******************************************************************************
  */
/* USER CODE END Header */

/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "stm32f1xx_it.h"
/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
/* USER CODE END Includes */

/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN TD */

/* USER CODE END TD */

/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */

/* USER CODE END PD */

/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM */

/* USER CODE END PM */

/* Private variables ---------------------------------------------------------*/
/* USER CODE BEGIN PV */

/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
/* USER CODE BEGIN PFP */
extern void prvvUARTTxReadyISR(void);
extern void prvvUARTRxISR(void);
extern void prvvTIMERExpiredISR( void );

/* USER CODE END PFP */

/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

/* External variables --------------------------------------------------------*/
extern DMA_HandleTypeDef hdma_i2c1_rx;
extern DMA_HandleTypeDef hdma_i2c1_tx;
extern I2C_HandleTypeDef hi2c1;
extern TIM_HandleTypeDef htim3;
extern UART_HandleTypeDef huart1;
/* USER CODE BEGIN EV */

/* USER CODE END EV */

/******************************************************************************/
/*           Cortex-M3 Processor Interruption and Exception Handlers          */
/******************************************************************************/
/**
  * @brief This function handles Non maskable interrupt.
  */
void NMI_Handler(void)
{
  /* USER CODE BEGIN NonMaskableInt_IRQn 0 */

  /* USER CODE END NonMaskableInt_IRQn 0 */
  /* USER CODE BEGIN NonMaskableInt_IRQn 1 */
  while (1)
  {
  }
  /* USER CODE END NonMaskableInt_IRQn 1 */
}

/**
  * @brief This function handles Memory management fault.
  */
void MemManage_Handler(void)
{
  /* USER CODE BEGIN MemoryManagement_IRQn 0 */

  /* USER CODE END MemoryManagement_IRQn 0 */
  while (1)
  {
    /* USER CODE BEGIN W1_MemoryManagement_IRQn 0 */
    /* USER CODE END W1_MemoryManagement_IRQn 0 */
  }
}

/**
  * @brief This function handles Prefetch fault, memory access fault.
  */
void BusFault_Handler(void)
{
  /* USER CODE BEGIN BusFault_IRQn 0 */

  /* USER CODE END BusFault_IRQn 0 */
  while (1)
  {
    /* USER CODE BEGIN W1_BusFault_IRQn 0 */
    /* USER CODE END W1_BusFault_IRQn 0 */
  }
}

/**
  * @brief This function handles Undefined instruction or illegal state.
  */
void UsageFault_Handler(void)
{
  /* USER CODE BEGIN UsageFault_IRQn 0 */

  /* USER CODE END UsageFault_IRQn 0 */
  while (1)
  {
    /* USER CODE BEGIN W1_UsageFault_IRQn 0 */
    /* USER CODE END W1_UsageFault_IRQn 0 */
  }
}

/**
  * @brief This function handles Debug monitor.
  */
void DebugMon_Handler(void)
{
  /* USER CODE BEGIN DebugMonitor_IRQn 0 */

  /* USER CODE END DebugMonitor_IRQn 0 */
  /* USER CODE BEGIN DebugMonitor_IRQn 1 */

  /* USER CODE END DebugMonitor_IRQn 1 */
}

/******************************************************************************/
/* STM32F1xx Peripheral Interrupt Handlers                                    */
/* Add here the Interrupt Handlers for the used peripherals.                  */
/* For the available peripheral interrupt handler names,                      */
/* please refer to the startup file (startup_stm32f1xx.s).                    */
/******************************************************************************/

/**
  * @brief This function handles DMA1 channel6 global interrupt.
  */
void DMA1_Channel6_IRQHandler(void)
{
  /* USER CODE BEGIN DMA1_Channel6_IRQn 0 */

  /* USER CODE END DMA1_Channel6_IRQn 0 */
  HAL_DMA_IRQHandler(&hdma_i2c1_tx);
  /* USER CODE BEGIN DMA1_Channel6_IRQn 1 */

  /* USER CODE END DMA1_Channel6_IRQn 1 */
}

/**
  * @brief This function handles DMA1 channel7 global interrupt.
  */
void DMA1_Channel7_IRQHandler(void)
{
  /* USER CODE BEGIN DMA1_Channel7_IRQn 0 */

  /* USER CODE END DMA1_Channel7_IRQn 0 */
  HAL_DMA_IRQHandler(&hdma_i2c1_rx);
  /* USER CODE BEGIN DMA1_Channel7_IRQn 1 */

  /* USER CODE END DMA1_Channel7_IRQn 1 */
}

/**
  * @brief This function handles TIM3 global interrupt.
  */
void TIM3_IRQHandler(void)
{
  /* USER CODE BEGIN TIM3_IRQn 0 */

  /* USER CODE END TIM3_IRQn 0 */
  HAL_TIM_IRQHandler(&htim3);
  /* USER CODE BEGIN TIM3_IRQn 1 */

  /* USER CODE END TIM3_IRQn 1 */
}

/**
  * @brief This function handles I2C1 event interrupt.
  */
void I2C1_EV_IRQHandler(void)
{
  /* USER CODE BEGIN I2C1_EV_IRQn 0 */

  /* USER CODE END I2C1_EV_IRQn 0 */
  HAL_I2C_EV_IRQHandler(&hi2c1);
  /* USER CODE BEGIN I2C1_EV_IRQn 1 */

  /* USER CODE END I2C1_EV_IRQn 1 */
}

/**
  * @brief This function handles USART1 global interrupt.
  */
void USART1_IRQHandler(void)
{
  /* USER CODE BEGIN USART1_IRQn 0 */

  /* USER CODE END USART1_IRQn 0 */
  HAL_UART_IRQHandler(&huart1);
  /* USER CODE BEGIN USART1_IRQn 1 */
	if(__HAL_UART_GET_IT_SOURCE(&huart1, UART_IT_RXNE)!= RESET) 
		{
			prvvUARTRxISR();//接收中断
		}

	if(__HAL_UART_GET_IT_SOURCE(&huart1, UART_IT_TXE)!= RESET) 
		{
			prvvUARTTxReadyISR();//发送中断
		}
	
  HAL_NVIC_ClearPendingIRQ(USART1_IRQn);
  HAL_UART_IRQHandler(&huart1);
  /* USER CODE END USART1_IRQn 1 */
}

/* USER CODE BEGIN 1 */
void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef *htim)	//定时器中断回调函数，用于连接porttimer.c文件的函数
{
  /* NOTE : This function Should not be modified, when the callback is needed,
            the __HAL_TIM_PeriodElapsedCallback could be implemented in the user file
   */
  	prvvTIMERExpiredISR( );
}
/* USER CODE END 1 */

demo.c文件：

/* ----------------------- Modbus includes ----------------------------------*/
#include "mb.h"
#include "mbport.h"
#include "AHT20-21_DEMO_V1_3.h" 

/* ----------------------- Defines ------------------------------------------*/
#define REG_INPUT_START 0
#define REG_INPUT_NREGS 5

/* ----------------------- Static variables ---------------------------------*/
static USHORT   usRegInputStart = REG_INPUT_START;
//static 
uint16_t   usRegInputBuf[REG_INPUT_NREGS];
uint16_t InputBuff[5];
uint32_t CT_data[2]={0,0};
	volatile int  c1,c2,t1,t2;

eMBErrorCode
eMBRegInputCB( UCHAR * pucRegBuffer, USHORT usAddress, USHORT usNRegs )
{
    eMBErrorCode    eStatus = MB_ENOERR;
    int             iRegIndex;
		int             i;
		AHT20_Read_CTdata_crc(CT_data);  //crc校验后，读取AHT20的温度和湿度数据 
		c1 = CT_data[0]*1000/1024/1024;  //计算得到湿度值c1（放大了10倍）
		t1 = CT_data[1]*2000/1024/1024-500;//计算得到温度值t1（放大了10倍）
		c2 = c1/10 + (c1/10)%10;
		t2 = t1/10 + (t1/10)%10;
		InputBuff[0] = t2;
		InputBuff[1] = c2;
		InputBuff[2] = 0x01;
		InputBuff[3] = 0x01;
		
    if( ( usAddress >= REG_INPUT_START )
        && ( usAddress + usNRegs <= REG_INPUT_START + REG_INPUT_NREGS ) )
    {
        iRegIndex = ( int )( usAddress - usRegInputStart );
				for(i=0;i<usNRegs;i++)
				{
					*pucRegBuffer=InputBuff[i+usAddress-1]>>8;
					pucRegBuffer++;
					*pucRegBuffer=InputBuff[i+usAddress-1]&0xff;
					pucRegBuffer++;
				}
    }
    else
    {
        eStatus = MB_ENOREG;
    }

    return eStatus;
}

eMBErrorCode
eMBRegHoldingCB( UCHAR * pucRegBuffer, USHORT usAddress, USHORT usNRegs,
                 eMBRegisterMode eMode )
{
    return MB_ENOREG;
}


eMBErrorCode
eMBRegCoilsCB( UCHAR * pucRegBuffer, USHORT usAddress, USHORT usNCoils,
               eMBRegisterMode eMode )
{
    return MB_ENOREG;
}

eMBErrorCode
eMBRegDiscreteCB( UCHAR * pucRegBuffer, USHORT usAddress, USHORT usNDiscrete )
{
    return MB_ENOREG;
}

然后编译运行

结果展示

由于没有硬件设备，这里就不做展示

Glock1e_bae
关注
  • 0
    点赞
  • 踩
  • 0
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
用stm32最小核心板+AHT20模块，完成一个 modbus接口的温湿度Slave设备，能够让上位机PC通过modbus协议获取温湿度。
m0_51592017的博客
12-24 228
整体步骤较繁琐，每一步都需要认真仔细。
STM32使用Modbus协议读取温湿度
apple_52030329的博客
12-25 2309
软件版本Keil 531硬件AHT20温湿度传感器题目要求用stm32最小核心板+AHT20模块，完成一个 modbus接口的温湿度Slave设备，能够让上位机PC通过modbus协议获取温湿度。主程序采用多任务框架，比如RT-thread Nano。本次实验进一步学习了解了Modbus协议的应用，同时还完成了RT-Thread的移植。
A22 STM32_HAL库函数 之 I2c通用驱动程序 -- C -- 所有函数的介绍及使用
qq_50808730的博客
04-16 856
以上就是该博客驱动所有函数的介绍及使用的内容。有不明白的地方欢迎留言；有建议欢迎留言，我后面编写文档好改进。创作不容，如果文档对您有帮助，记得给个赞。
stm32通过I2C接口实现温湿度（AHT20）的采集
weixin_56102526的博客
11-21 5077
stm32通过I2C接口实现温湿度（AHT20）的采集一、I2C总线协议详解（一）I2C总线物理拓扑结构（二)I2C总线协议（三）硬件I2C和模拟I2C1.硬件I2C2.模拟I2C3.区别二、实现AHT20采集程序（一）了解AHT20芯片的相关信息（二）具体代码添加过程（三）主要代码的分析（四）线路接法（五）运行结果三、总结四、参考资料 一、I2C总线协议详解 （一）I2C总线物理拓扑结构 I2C 总线在物理连接上非常简单，分别由SDA(串行数据线)和SCL(串行时钟线)及上拉电阻组成。通信原理是通过对S
STM32 KEIL编写 Modbus RTU Master slave程序源码
04-29
STM32 KEIL 编写的可移植 Modbus RTU 协议主站和从站程序源码 亲测可用 课根据需要移植 希望帮到需要的人 我也是通过网络学习 现在回馈网络
FreeModbus for stm32（Keil工程）——精简Modbus slave协议【worlsing笔记】
weixin_30906701的博客
11-25 1001
FreeModbus For stm32:点击下载源码 1、测试环境Keil MDK 4.7a stm32f103c8， PB12为输出线圈， 可以通过Modbus Poll来控制线圈的输出状态。 2、通过ModbusProt.h配置硬件、数据缓冲区大小和功能码配置 #define UART_USE ...
Modbus Slave version 9.3.2 Build 2156
最新发布
05-17
Modbus Slave version 9.3.2 Build 2156， modbus 协议从机，非常好用，包括32位与64位
Modbus Slave 7.4.4
03-02
Modbus Slave 7.4.4
【软件下载】Modbus Poll 7.0.1 + Modbus Slave 6.1.3
06-17
资源简介：Modbus Poll是一个模拟Modbus协议主机的上位机软件，主要用于模拟测试跟其他从机设备通信的过程。该软件内部封装标准Modbus协议栈，通过图形化界面使得操作更为简便。目前软件支持01、02、03、04、05、06...
Modbus Slave： Modbus从设备仿真器
08-25
Modbus Slave： Modbus从设备仿真器
设备模拟软件 modbusslave.zip
11-17
设备模拟软件 modbusslave.zip
stm32l151 STM32L1xxx I2C配置与读写
01-09
详细描述了I2C的配置，在STM32L15XX系列的。 网上很多STM32F的资料而这个是L系列的，能读写从机设备。
Thingsboard modbus协议
Zzhou1990的博客
03-02 5480
一直没有整理，今天测试整理一下，方便以后配置。 Modbus协议 modbus协议是一种应用层协议，可以通过OSI第四-7层传输层协议TCP/IP协议来传输，也可以通过OSI第1-2-7层串行链路上的RTU和ASCII来传输。 一般来说，通讯数据量少而且主要是文本的通讯则采用MODBUS ASCII规约，通讯数据数据量大而且是二进制数值时，多采用MODBUS RTU规约。 modbus-r...
keil5下c语言modbus函数_Modbus协议简要说明「超级实用」
weixin_34461414的博客
12-24 1440
Modbus是一种串行通信协议，是Modicon公司(现在的施耐德电气 Schneider Electric)于1979年为使用可编程逻辑控制器(PLC)通信而发表。Modbus已经成为工业领域通信协议的业界标准(De facto)，并且现在是工业电子设备之间常用的连接方式。Modbus协议有三种(Modbus-RTU(串口)、Modbus-ASCII(串口)、Modbus-TCP(以太网))。简...
移植RT-thread Nano完成一个 modbus接口的温湿度Slave设备，让上位机PC通过modbus协议获取温湿度
qq_52215423的博客
12-30 1030
移植RT-thread Nano完成一个 modbus接口的温湿度Slave设备，让上位机PC通过modbus协议获取温湿度
ThingsBoard使用笔记（4）配置tb-gateway 网关接入 Modbus
qq_31867231的博客
07-22 5134
配置modbus模拟环境 安装串口模拟工具Virtual Serial Port Kit Virtual Serial Port Kit是一款好用的虚拟串口调试软件，可以创建一对与虚拟零调制解调器电缆连接的虚拟串口，通过虚拟com端口相互交互，可自定义脚本和环回插件仿真，具有自动错误纠正、自动连接和自动重新调试等功能， virtual-serial-port-kit.zip 下载地址：http://www.opdown.com/soft/125086.html 下载之后一路下一步安装，然后打开模拟工具 点
Modbus RTU（Remote Terminal Unit）与RS-485协议（rs485）介绍（主站设备（Master）、从站设备（Slave））Modbus TCP、Modbus ASCII
Dontla的博客
09-18 6640
参考文章：ModBus协议参考文章：一篇文章了解 RS485 和 MODBUS 的区别，它们有什么不同？Modbus RTU（Remote Terminal Unit）协议是Modbus协议的一种，主要应用于工业自动化系统中。它以二进制形式传输数据，并采用CRC校验方式确保数据的正确性1。RS-485 是一种差分信号传输方式，其主要优点在于具有较高的抗电磁干扰能力和传输距离5。
PTP同步方式简单介绍 Master和Slave功能
l694066619的博客
03-24 2432
PTP简单介绍，及基本同步原理
STM32无限循环进入i2c事件中断卡死线程调度
lijunnanxcx的博客
05-30 3152
在开发项目中遇到RTT线程不调度的问题，现象是出现i2c报错，线程不调度，只响应中断。 问题是随机小概率出现，我们提出的几个推测点： 1.栈溢出 2.最高优先级的线程中有死循环 3.进入临界区关了调度锁 4.死锁 5.关RT中断 注：不要因为看了标题而先入为主 1.栈溢出 因为RTT没有FreeRTOS那样的API接口（或许我们没有找到），只能打印线程信息，栈起始地址、sp指针（可知道已使用栈大小）、优先级（担心优先级反转），时间片等。 void rt_memory_info(rt
modbus poll和modbus slave 通信
03-23
1. Modbus Poll是一个Modbus主站（Master）软件，用于模拟Modbus主站设备与Modbus从站（Slave）设备之间的通信。它可以通过串口、以太网等方式与Modbus从站设备进行通信，并发送读写命令来获取或设置从站设备的数据...

“相关推荐”对你有帮助么？

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值