实验四 STM32定时器控制LED灯

利用已经建立的工程模板，在Keil for ARM V5中编写代码，使用按键控制LED灯电路，实现如下功能：选择两个定时器，分别控制LED1和LED2，使得LED1每1秒钟改变一次状态，和LED2每2秒钟改变一次状态。

main.c

int main()
{
	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
	ST_Init();
	LED1 = 1; LED2 = 1;LED3 = 1;LED4 = 1;
	TIM2_Init(1000 - 1 , 7200 - 1);
	TIM3_Init(2000 - 1 , 7200 - 1);
	while(1)
	{
		
	}
}

st.c

#include "st.h"

void ST_Init()
{
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB , ENABLE); 
	GPIO_InitTypeDef GPIO_InitStructure;
	
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10 | GPIO_Pin_11;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
	GPIO_Init(GPIOB, &GPIO_InitStructure); 
	
	
}	

st.h

#ifndef __ST_H
#define __ST_H

#include "sys.h"

#define LED1 PBout(8)
#define LED2 PBout(9)
#define LED3 PBout(10)
#define LED4 PBout(11)

void ST_Init(void);

#endif

time.c

#include "time.h"
#include "st.h"

void TIM2_Init(u16 arr , u16 psc)
{
	RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2 , ENABLE);
	
	TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
  TIM_TimeBaseStructure.TIM_Period = arr;
  TIM_TimeBaseStructure.TIM_Prescaler = psc;
  TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1;
  TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
  TIM_TimeBaseInit(TIM2, & TIM_TimeBaseStructure); 
	TIM_ITConfig(TIM2, TIM_IT_Update, ENABLE );
	
	NVIC_InitTypeDef NVIC_InitStructure; 
	NVIC_InitStructure.NVIC_IRQChannel = TIM2_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2;
 	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
	
	TIM_Cmd(TIM2,ENABLE);
}

void TIM3_Init(u16 arr , u16 psc)
{
	RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3 , ENABLE);
	
	TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
  TIM_TimeBaseStructure.TIM_Period = arr;
  TIM_TimeBaseStructure.TIM_Prescaler = psc;
  TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV2;
  TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
  TIM_TimeBaseInit(TIM3, & TIM_TimeBaseStructure); 
	TIM_ITConfig(TIM3, TIM_IT_Update, ENABLE );
	
	NVIC_InitTypeDef NVIC_InitStructure; 
	NVIC_InitStructure.NVIC_IRQChannel = TIM3_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2;
 	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
	
	TIM_Cmd(TIM3,ENABLE);
}

void TIM2_IRQHandler()
{
		
	LED1=~LED1;
  TIM_ClearFlag(TIM2,TIM_IT_Update);  
}

void TIM3_IRQHandler()
{
		
	LED2=~LED2;
  TIM_ClearFlag(TIM3,TIM_IT_Update);  
}

time.h

#ifndef __TIME_H
#define __TIME_H

#include "sys.h"

void TIM1_Init(u16 arr , u16 psc);
void TIM2_Init(u16 arr , u16 psc);

#endif