炒冷饭系列-STM32F103之定时器PWM

淦，好累，不想写了。。。。。

#include "stm32f10x.h"
#include "LED.h"
#include "delay.h"
#include "tim.h"

void myPwmHandler(uint16_t prer,uint16_t value);
int main(void)
{	
	u8 dir=1;
	u16 led_pwm=0;
	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
	delay_init();	    	 //延时函数初始化
	LED_Init();
	myPwmHandler(0,899);Tout= ((arr+1)*(psc+1))/Tclk； 900/72=12us
	
	while(1)
	{
		delay_ms(10);
		if(dir)
		{
			led_pwm++;
		}else{
			led_pwm--;
		}
		
		if(led_pwm>=300)
		{
			dir=0;
		}
		
		if(led_pwm==0){
			dir=1;
		}
			
		
		
		TIM_SetCompare2(TIM3,led_pwm);//TIMx->CCR2 = Compare2; 与TIMx->CNT的值进行比较
	}
}

void myPwmHandler(uint16_t prer,uint16_t value)
{
	GPIO_InitTypeDef GPIO_InitStruct;
	TIM_TimeBaseInitTypeDef TIM_TimeBaseInitStruct;
	TIM_OCInitTypeDef TIM_OCInitStruct;
	
	//1、使能定时器时钟、复用(重映射)时钟  GPIO口时钟不用，因为没用到其输出或输入，只是借用一下而已
	RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);//使能定时器 3 时钟
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);//使能AFIO 复用功能时钟
	
	//2、GPIOB5管脚配置和复用
	GPIO_InitStruct.GPIO_Mode=GPIO_Mode_AF_PP;//复用推挽输出
	GPIO_InitStruct.GPIO_Pin=GPIO_Pin_5;//TIM_CH2
	GPIO_InitStruct.GPIO_Speed=GPIO_Speed_10MHz;
	GPIO_Init(GPIOB,&GPIO_InitStruct);
	
	//3、TIM3参数配置
	TIM_TimeBaseInitStruct.TIM_Prescaler=prer;//给TIM时钟分频：范围0x0000~0xFFFF=0~65535，对应预分频寄存器：TIMx->PSC
	TIM_TimeBaseInitStruct.TIM_CounterMode=TIM_CounterMode_Up;//计数模式：有5种，对应控制寄存器1：TIM_CR1_DIR位4 | TIM_CR1_CMS位[6:5]
	TIM_TimeBaseInitStruct.TIM_Period=value;//自动重装载值：0x0000 and 0xFFFF 对应自动重装载值寄存器：TIMx->ARR
	TIM_TimeBaseInitStruct.TIM_ClockDivision=0;//APB1时钟36MHz  分频72MHz    给APB1时钟分频：1,2,4 ,对应控制寄存器1：TIM_CR1_CKD位[9:8]
	TIM_TimeBaseInit(TIM3, &TIM_TimeBaseInitStruct);
	
	
	//4、TIM3重映射到PB5
	GPIO_PinRemapConfig(GPIO_PartialRemap_TIM3,ENABLE);//重映射 TIM3_CH2->PB5
	
	//OC：Output Compare输出比较 OC2的2是通道2
	//TIM_OCInitStruct.TIM_OCIdleState=TIM_OCIdleState_Set;
	TIM_OCInitStruct.TIM_OCMode=TIM_OCMode_PWM2;//通道PWM2
	//TIM_OCInitStruct.TIM_OCNIdleState=;
	//TIM_OCInitStruct.TIM_OCNPolarity=;
	TIM_OCInitStruct.TIM_OCPolarity=TIM_OCPolarity_High;//输出级性
	//TIM_OCInitStruct.TIM_OutputNState=;
	TIM_OCInitStruct.TIM_OutputState=TIM_OutputState_Enable;//比较输出使能
	//TIM_OCInitStruct.TIM_Pulse=;
	
	TIM_OC2Init(TIM3, &TIM_OCInitStruct);
	
	TIM_OC2PreloadConfig(TIM3, TIM_OCPreload_Enable); //使能预装载寄存器
	//5、使能定时器
	TIM_Cmd(TIM3,ENABLE);
	
}