如何调整Lutron Caseta调光器开关的亮度范围

Lutron’s Caseta dimmer switches are great, but if you’re having some issues with your lights flickering or turning off prematurely, you can adjust the dimming levels to eliminate these issues.

路创的Caseta调光器开关很棒，但是如果您遇到灯光闪烁或过早关闭的问题，则可以调整调光级别以消除这些问题。

The Caseta switches let you adjust the low-end and high-end “trim” levels, which is just a fancy term for optimizing the dimming levels on the light switch. So, for example, if your lights start to flicker a little when you dim them down past 10% or so, you can adjust the trim so that 10% is the lowest it goes, thus eliminating the flicker.

Caseta开关可让您调整低端和高端“微调”电平，这只是优化照明开关上的调光电平的一个花哨的名词。 因此，例如，如果当您将灯光调暗到10％左右时，您的灯光开始有点闪烁，则可以调整修剪，使10％达到最低，从而消除了闪烁。

You may also run into situations where your lights turn off completely when you dim them down all the way, or the brightest setting may just be way too bright for your needs. You can adjust for those problems, too! Let’s get started.

您也可能会遇到这样的情况，当您将其完全调暗时，您的灯会完全关闭，或者最亮的设置可能太亮而无法满足您的需求。 您也可以针对这些问题进行调整！ 让我们开始吧。

首先，请确保您使用的是兼容灯泡 (First Off, Make Sure You’re Using Compatible Bulbs)

Before you blame the issue on the light switch itself, make sure that your light bulbs are actually compatible with the Lutron Caseta switches.

在将问题归咎于电灯开关本身之前，请确保您的灯泡实际上与Lutron Caseta开关兼容。

You can take a look at Lutron’s compatibility tool to search for light bulbs that work with your light switch, but the most common mistake people make is using non-dimmable bulbs with their dimmer switches. A lot of cheaper LED bulbs aren’t dimmable, so it’s always a good idea to look on the bulb’s packaging to make sure that it can be used with a dimmer switch.

您可以看一下路创的兼容性工具来搜索可与您的电灯开关配合使用的灯泡，但是人们最常犯的错误是将不可调光的灯泡与调光开关一起使用。 许多便宜的LED灯泡是不可调光的，因此始终看一下灯泡的包装以确保它可与调光开关一起使用始终是个好主意。

Other than that, though, as long as the bulb is dimmable, it should work just fine. However, there’s always the possibility of the bulb not fully cooperating. That’s when you want to adjust the trim levels.

但是除此之外，只要灯泡是可调光的，它就可以正常工作。 但是，灯泡始终可能无法完全配合。 那是您要调整修剪水平的时候。

调整低端和高端修剪 (Adjusting the Low-End and High-End Trims)

To adjust the low-end trim (i.e., how dim the lights can get), press down and hold the On and Down buttons at the same time for around six seconds.

要调整低端装饰(例如，灯光可以变暗的程度)，请同时按下并按住“打开”和“向下”按钮约六秒钟。

The small green LED light should begin flashing.

绿色小LED指示灯应开始闪烁。

Press the Down button until the lights are as dim as possible (they might turn off completely, which is normal). Keep pressing the Down button just to confirm that the dimmer switch is as dim as possible.

按下“向下”按钮，直到灯光尽可能暗(它们可能会完全关闭，这是正常现象)。 持续按下“向下”按钮只是为了确认调光器开关尽可能暗。

Next, slowly press the Up button to brighten the lights. Once any flickering stops or the bulb is at a stable dim setting that you’re happy with, press and hold the Off button until the small flashing LED light on the switch turns off.

接下来，慢慢按下向上按钮以点亮灯光。 一旦任何闪烁停止或灯泡处于您满意的稳定暗淡设置，请按住“关闭”按钮，直到开关上的小闪烁LED灯熄灭。

That’s all there is to it! Repeat the above steps for the high-end trim, but simply reversing the Up and Down buttons.

这里的所有都是它的！ 对高端修剪重复上述步骤，但只需反转“向上”和“向下”按钮即可。

翻译自: https://www.howtogeek.com/348431/how-to-adjust-the-brightness-range-of-your-lutron-caseta-dimmer-switches/