全志平台Tina系统htol测试

HTOL 高温使用寿命测试(High Temperature Operating Life)

用于测试设备在高温下数周之后的功能/性能情况

一般是125°C(cpu温度传感器捕捉到的温度)+ 1000小时

 

测试固件要求

1.设备跑在最高频率(以R328为例,跑在1.0V @1.2G Hz的频率下),所以调频策略最好选userspace,手动设置最高频,但也可以跑performance模式,默认跑当前最高,所以也要把最高设置上去

        如果当前设备最高没有配1.2G,要把1.2G配上,在源码dts里修改:

tina/lichee/linux-4.9/arch/arm/boot/dts$ git diff . diff --git a/arch/arm/boot/dts/sun8iw18p1-cowbell-perf1.dts b/arch/arm/boot/dts/ index 16a093d..4df621d 100644 --- a/arch/arm/boot/dts/sun8iw18p1-cowbell-perf1.dts +++ b/arch/arm/boot/dts/sun8iw18p1-cowbell-perf1.dts @@ -45,7 +45,7 @@                 cpu_opp_l_table0: opp_l_table0 {                                 /* compatible = "operating-points-v2"; */                                 compatible = "allwinner,opp_l_table0"; -                               opp_count = <2>; +                               opp_count = <3>;                                 opp-shared;                                   opp00 { @@ -61,6 +61,13 @@                                         axi-bus-divide-ratio = <3>;                                         clock-latency-ns = <2000000>;                                 }; + +                               opp02 { +                                       opp-hz = /bits/ 64 <1200000000>; +                                       opp-microvolt = <1000000>; +                                       axi-bus-divide-ratio = <3>; +                                       clock-latency-ns = <2000000>; +                               };                 };         };  };

      

       把1.2G写进去:echo 1200000 > /sys/devices/system/cpu/cpufreq/policy0/scaling_setspeed

       确认是否已经跑在1.2G: cat /sys/devices/system/cpu/cpufreq/policy0/scaling_cur_freq        

 

2.把温控去掉,不然设备会因为跑在高温下降频了,不能起到测试效果

        make_kernelmenuconfig -> Device Driver -> Generic Thermal sysfs driver ,这个是温度控制器,去掉就不会温度调节了

 

3.基本功能包括WiFi\bt\mic\audio\led等功能要编进固件里,测试时间到了之后,要测试设备是否依然全功能完好

        wifi命令:wifi_connect_ap_test "ssid" "password"

        bt命令:bt_tesg

        录音命令:arecord -D "hw:0,0" -c 2 -r 44100 -f s24_le /tmp/record.wav

        播放声音命令:aplay -D "hw:0,0" /tmp/record.wav

        led命令:

        红灯亮：echo 255 >   /sys/devices/platform/soc/ledc/leds/sunxi_led0r/brightness

        红灯灭：echo 0 >   /sys/devices/platform/soc/ledc/leds/sunxi_led0r/brightness

       绿灯亮：echo 255 >   /sys/devices/platform/soc/ledc/leds/sunxi_led0g/brightness

        绿灯亮：echo 0 >   /sys/devices/platform/soc/ledc/leds/sunxi_led0g/brightness

        蓝灯亮：echo 255 > /sys/devices/platform/soc/ledc/leds/sunxi_led0b/brightness        

        蓝灯灭：echo 0 > /sys/devices/platform/soc/ledc/leds/sunxi_led0b/brightness

 

 

 

4.音频类产品同时打开唤醒demo+播放音乐,模拟真实场景

        make menuconfig -> Thirdparty -> demo选中,或者其他demo选中

        修改时间:date -s "2018-12-25 00:01:01"

        

5.memtester 要在,跑demo剩余的内存都用来跑memtester

        make menuconfig -> utilities -> memtester选中

        memtester命令:memtester 10M (申请10M内存,不加数字参数默认无限循环测试,加数字参数则代表循环测试的次数)

 

6.dram:
        使用推荐值/默认值528M,如果要改可以echo允许的数值(最小240)到/sys/firmware/devicetree/base/dram/dram_clk 里或者到sys_config.fex里,关键字也是dram_clk