FPGA的串口的收发程序设计

module uart_tx(
  input clk,
  input rst,
  input start,
  input [7:0] data,
  output reg tx_done,
  output reg tx_out
);

  // 定义状态机的状态
  typedef enum logic [2:0] {
    IDLE, START, DATA, STOP
  } state_t;

  reg [10:0] count;     // 用于计数发送的位数
  reg [2:0] state;      // 用于记录状态机的当前状态
  reg [7:0] tx_data;    // 用于暂存要发送的数据

  always @(posedge clk) begin
    if (rst) begin
      state <= IDLE;
      count <= 0;
      tx_done <= 0;
      tx_out <= 1;      // 初始化时设置为停止位
    end else begin
      case (state)
        IDLE: begin
          if (start) begin
            tx_data <= data;
            state <= START;
            count <= 0;
            tx_done <= 0;
            tx_out <= 0; // 开始位
          end
        end

        START: begin
          if (count < 8) begin
            tx_out <= tx_data[count];
            count <= count + 1;
          end else begin
            state <= DATA;
            count <= 0;
          end
        end

        DATA: begin
          if (count < 8) begin
            tx_out <= tx_data[count];
            count <= count + 1;
          end else begin
            state <= STOP;
            count <= 0;
          end
        end

        STOP: begin
          if (count < 2) begin
            tx_out <= 1; // 停止位
            count <= count + 1;
          end else begin
            state <= IDLE;
            count <= 0;
            tx_done <= 1;
          end
        end
      endcase
    end
  end

endmodule

module uart_rx(
  input clk,
  input rst,
  input rx_in,
  output reg [7:0] rx_data,
  output reg rx_done
);

  // 定义状态机的状态
  typedef enum logic [2:0] {
    IDLE, START, DATA, STOP
  } state_t;

  reg [10:0] count;     // 用于计数接收的位数
  reg [2:0] state;      // 用于记录状态机的当前状态
  reg [7:0] rx_temp;    // 用于暂存接收的数据

  always @(posedge clk) begin
    if (rst) begin
      state <= IDLE;
      count <= 0;
      rx_temp <= 0;
      rx_data <= 0;
      rx_done <= 0;
    end else begin
      case (state)
        IDLE: begin
          if (!rx_in) begin
            state <= START;
            count <= 0;
            rx_temp <= 0;
          end
        end

        START: begin
          if (count < 8) begin
            rx_temp[count] <= rx_in;
            count <= count + 1;
          end else begin
            state <= DATA;
            count <= 0;
          end
        end

        DATA: begin
          if (count < 8) begin
            rx_temp[count] <= rx_in;
            count <= count + 1;
          end else begin
            state <= STOP;
            count <= 0;
          end
        end

        STOP: begin
          if (count < 2) begin
            count <= count + 1;
          end else begin
            state <= IDLE;
            rx_data <= rx_temp;
            rx_done <= 1;
          end
        end
      endcase
    end
  end

endmodule
 

上述代码定义了两个模块,一个是uart_tx模块用于实现UART发送功能,另一个是uart_rx模块用于实现UART接收功能。

uart_tx模块根据输入的start信号和data数据进行串口数据的发送。start信号认为是发送起始信号,data数据是要发送的8位数据。在clk的上升沿时,状态机根据当前状态进行相应的操作,包括发送开始位、数据位和停止位。最后输出tx_done信号表示发送完成,tx_out为串口发送的数据信号。

uart_rx模块根据输入的rx_in信号接收串口数据,并将接收到的数据存储在rx_data寄存器中。在clk的上升沿时,状态机根据当前状态进行相应的操作,包括接收开始位、数据位和停止位。最后输出rx_done信号表示接收完成,rx_data为接收到的数据。

以上代码仅为示例,实际使用时可能需要根据具体的需求进行相应的修改。

  • 2
    点赞
  • 0
    收藏
    觉得还不错? 一键收藏
  • 打赏
    打赏
  • 0
    评论

“相关推荐”对你有帮助么?

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包

打赏作者

战斗的青春岁月

你的鼓励将是我创作的最大动力

¥1 ¥2 ¥4 ¥6 ¥10 ¥20
扫码支付:¥1
获取中
扫码支付

您的余额不足,请更换扫码支付或充值

打赏作者

实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值