全志平台Android系统wifi模组rtl8188eu移植调试记录

最新推荐文章于 2024-10-11 07:49:27 发布
最新推荐文章于 2024-10-11 07:49:27 发布
阅读量1.7k 收藏 2
点赞数
分类专栏： 全志平台开发 文章标签： android linux
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/bingdund/article/details/123104077
版权
本文记录了在全志A3x平台上，针对Android 4.4.2系统，移植和调试rtl8188eu USB WiFi模组的详细步骤，包括内核配置、引脚配置、电源管理修改以及Android平台的配置调整，以实现station、softAP和wifi direct功能。
摘要由CSDN通过智能技术生成

1. 前言

A3x android4.4.2平台；

rtl8188eu是一款USB接口的wifi模组，支持802.11b/g/n协议，具有station、softAP和wifi direct功能。

2. 内核配置

rtl8188eu模组所使用的驱动为8188eu，代码位于lichee/linux-3.3/drivers/net/wireless/rtl8188eu目录，配置内核将该驱动编译为模块，

在linux-3.3目录下执行make ARCh=arm menuconfig命令，做以下选择：

Device Drivers --->
       Network device support--->
               Wireless LAN--->
                       <M> Realtek 8188E USB WiFi

配置完后编译内核。

3. 引脚配置

rtl8188eu的引脚配置在lichee/tools/pack_brandy/chips/sun6i/configs/android/fiber-evb/sys_config.fex中定义，需要修改的地方有两个，首先是wifi配置：

;wifi configuration
;wifi_sdc_id    ---  0- SDC0, 1- SDC1, 2- SDC2,
了解本专栏 订阅专栏 解锁全文 超级会员免费看
RK3568平台（网络篇）WIFI模块RTL8821CU调试
weixin_49303682的博客
10-14 2366
RTL8821CU是瑞昱半导体推出的usb接口的wifi，下面的教程将介绍如何将RTL8821CU移植到rk3588的平台上。移植usb wifi需要修改的文件Android hal层需要修改的文件//kernel需要修改的文件kernel/arch/arm64/boot/dts/rockchip/rk3399-tve1030g.dtsi //除去板上的sdio的wifi。
全志A31平台WIFI移植
11-19
A31(s)平台android4.4 wifi模块移植说明文档_20140312
移植wifi驱动到android,移植rtl8188 wifi模块到android 8.1(android o)
weixin_42153793的博客
05-26 1262
一、驱动部分1、rtl8188eu/rtl8188fu驱动，修改对应目录下的makefile，适应平台2、检测模块电压、时钟是否正确。硬件正常的话，可以用lsusb查看到模块的厂商ID和设备ID。3、加载驱动后， ifconfig -a可以看到网口，用iw命令测试wifi，能扫描出附近的热点，说明硬件和驱动部分没什么问题二、安卓层需要根据realtek文档做一些修改，andorid 8需要在启动脚...
rtl8188eus 项目安装与使用教程
最新发布
gitblog_00533的博客
10-11 846
rtl8188eus 项目安装与使用教程 rtl8188eus Wifi driver support for rtl8188eu, rtl8188eus and rtl8188etv chips and working under the new linux kernel (5.1.x). ...
明远智睿IMX6Q Android4.4.2移植USBWIFI(RTL8188EUS)
xiaoyaofriend的专栏
05-18 4137
移植过程中得到网友的不少帮助，很感谢!为了让更多的网友不像我这样折腾，特写此文以做参照.过程中主要参考和这两个文档，以及论坛https://community.freescale.com/thread/322825 这篇文章，具体步骤如下：   一．内核修改 1．替换realtek文件夹 ”realtek_wifi_SDK_for_android_KK_4.4_20140117.tar.g
如何把rtl8188EUS驱动编译生成ko模块并且下载到rk平台Android4.2.2上使用
weixin_33671935的博客
07-17 410
下了rtl8188EUS_linux_v4.3.24_16705.20160509.tar.gz，看了里面的数据手册，发现有些看不懂，上网搜了一下，发现大部分博客都在扯淡。。。后来还是我把Makefile一句一句的看完才知道怎么做。 具体应该怎么编译成我需要的模块呢？我的平台是rk3168。 1、解压缩rtl8188EUS_linux_v4.3.2...
RTL8188EU
weixin_45349398的博客
10-15 1009
allow_signal signal_pending flush_signals 这三个函数问题 显示未定义函数 头文件添加 #include <linux/sched/signal.h> #include <linux/uaccess.h>
嵌入式 移植 rtl8188eu
weixin_42583683的博客
01-05 296
rtl8188eu 是一种无线网卡芯片，如果要在嵌入式系统中使用它，那么就需要将其移植到该系统中。 移植 rtl8188eu 的具体步骤如下： 下载 rtl8188eu 驱动源码，可以在 Realtek 官网或者其他网站上获取。 将源码移植到嵌入式系统，这一步可能需要修改源码中的一些内容，使其适配嵌入式系统的硬件和操作系统。 编译驱动源码，生成可在嵌入式系统中使用的驱动文件。 将驱动文件安...
君正T31 平台移植wifi 模块rtl8188 的问题及解决方法.docx
03-11
在本文档中，主要讨论了在君正T31平台上移植WiFi模块RTL8188时遇到的问题及其解决策略。该文档适用于具有嵌入式移植经验的开发人员，特别是那些在Linux环境下对WiFi模块移植有一定了解，但在移植wpa_supplicant工具...
cubieboard2_csi01_2ov7670_rtl8188eus在marsboard上面打开wifi20150904_1820.7z
09-04
根据全志a20的WIFI移植手册，可以看见rtl8188eus是默认配置的。只是电源不是文字（系统的电源芯片AXP供电），在启动的时候直接就退出了，变成不可控制了！ Y:\wyb\marsboard_lcd5inch_video0_csi0_ov7670\cubieboard...
rtl8188eu驱动源码.zip
06-18
适用于Linux4.x版本的无线网卡芯片rtl8188eu的C语言驱动源码。包含驱动所需的头文件、源文件以及makefile、Kconfig文件。可以借助内核源码编译出.ko驱动文件，也可以通过修改代码后直接编译综合到内核文件中，使生成的内核文件可以驱动rtl8188无线网卡。
rtl8188eu_sina33m_sc3817在服务器最终验证版本_20170710_1106.7z
07-10
调通sina33m下的RTL8188EU版本 大文实验室/大文哥 壹捌陆捌零陆捌捌陆捌贰 wb4916 AT qq.com 完成时间：2017/7/7 18:11 版本：V1.0 SDK：Android6.0.1 开发板：SC3817R 1、干掉设置中的BT蓝牙选项： R:\wyb\rtl8188eu_sina33m_sc3817\android\device\softwinner\astar-d7\overlay\frameworks\base\core\res\res\values\config.xml <!-- List of regexpressions describing the interface (if any) that represent tetherable bluetooth interfaces. If the device doesn't want to support tethering over bluetooth this should be empty. --> <!-- default: disable Bluetooth PAN feature --> <string-array translatable="false" name="config_tether_bluetooth_regexs"> <item>"bt-pan"</item> </string-array> 2、干掉BT（特别是rtl8723bs的）： R:\wyb\rtl8188eu_sina33m_sc3817\android\device\softwinner\astar-d7\astar_d7.mk PRODUCT_PACKAGES += Launcher3 PRODUCT_PACKAGES += \ ESFileExplorer \ VideoPlayer #Bluetooth PRODUCT_COPY_FILES += \ frameworks/native/data/etc/android.hardware.camera.xml:system/etc/permissions/android.hardware.camera.xml \ frameworks/native/data/etc/android.hardware.camera.front.xml:system/etc/permissions/android.hardware.camera.front.xml \ frameworks/native/data/etc/android.hardware.ethernet.xml:system/etc/permissions/android.hardware.ethernet.xml \ frameworks/native/data/etc/android.hardware.wifi.xml:system/etc/permissions/android.hardware.wifi.xml \ frameworks/native/data/etc/android.hardware.wifi.direct.xml:system/etc/permissions/android.hardware.wifi.direct.xml #frameworks/native/data/etc/android.hardware.bluetooth.xml:system/etc/permissions/android.hardware.bluetooth.xml \ #frameworks/native/data/etc/android.hardware.bluetooth_le.xml:system/etc/permissions/android.hardware.bluetooth_le.xml #PRODUCT_COPY_FILES += \ # device/softwinner/astar-d7/bluetooth/bt_vendor.conf:system/etc/bluetooth/bt_vendor.conf # bootanimation PRODUCT_COPY_FILES += \ device/softwinner/astar-d7/media/bootanimation.zip:system/media/bootanimation.zip # camera config for camera detector #PRODUCT_COPY_FILES += \ # device/softwinner/astar-d7/hawkview/sensor_list_cfg.ini:system/etc/hawkview/sensor_list_cfg.ini PRODUCT_PROPERTY_OVERRIDES += \ persist.sys.usb.config=mass_storage,adb \ ro.adb.secure=0 \ ro.sys.mutedrm=true \ rw.logger=0 #$(call inherit-product-if-exists, vendor/google/products/gms_base.mk) #for 8723bs-vq0,should setmacaddr #PRODUCT_PACKAGES += setmacaddr #for 8723bs-vq0,should setbtmacaddr #PRODUCT_PACKAGES += setbtmacaddr 3、 R:\wyb\rtl8188eu_sina33m_sc3817\android\device\softwinner\astar-d7\BoardConfig.mk BOARD_WIFI_VENDOR := realtek ifeq ($(BOARD_WIFI_VENDOR), realtek) WPA_SUPPLICANT_VERSION := VER_0_8_X BOARD_WPA_SUPPLICANT_DRIVER := NL80211 BOARD_WPA_SUPPLICANT_PRIVATE_LIB := lib_driver_cmd_rtl BOARD_HOSTAPD_DRIVER := NL80211 BOARD_HOSTAPD_PRIVATE_LIB := lib_driver_cmd_rtl #BOARD_USR_WIFI := rtl8723bs BOARD_USR_WIFI := rtl8188eu include hardware/realtek/wlan/config/config.mk endif # 1.2 broadcom wifi support # BOARD_USR_WIFI:ap6181/ap6210/ap6212/ap6330/ap6335 #BOARD_WIFI_VENDOR := broadcom ifeq ($(BOARD_WIFI_VENDOR), broadcom) BOARD_WPA_SUPPLICANT_DRIVER := NL80211 WPA_SUPPLICANT_VERSION := VER_0_8_X BOARD_WPA_SUPPLICANT_PRIVATE_LIB := lib_driver_cmd_bcmdhd BOARD_HOSTAPD_DRIVER := NL80211 BOARD_HOSTAPD_PRIVATE_LIB := lib_driver_cmd_bcmdhd BOARD_WLAN_DEVICE := bcmdhd WIFI_DRIVER_FW_PATH_PARAM := "/sys/module/bcmdhd/parameters/firmware_path" BOARD_USR_WIFI := ap6212 include hardware/broadcom/wlan/bcmdhd/firmware/$(BOARD_USR_WIFI)/device-bcm.mk endif # 2. Bluetooth Configuration # make sure BOARD_HAVE_BLUETOOTH is true for every bt vendor # BOARD_HAVE_BLUETOOTH_NAME:rtl8723bs/rtl8723bs_vq0/rtl8723cs/ap6210/ap6212/ap6330/ap6335/ #BOARD_HAVE_BLUETOOTH := true # #BOARD_HAVE_BLUETOOTH_BCM := true #BOARD_HAVE_BLUETOOTH_NAME := ap6212 # ##BOARD_HAVE_BLUETOOTH_RTK_COEX := true ##BOARD_HAVE_BLUETOOTH_RTK := true ##BLUETOOTH_HCI_USE_RTK_H5 := true # #BOARD_BLUETOOTH_BDROID_BUILDCFG_INCLUDE_DIR := device/softwinner/astar-d7/bluetooth 4、（干掉AP6212，打开RTL8188EU：） R:\wyb\rtl8188eu_sina33m_sc3817\android\device\softwinner\astar-d7\init.sun8i.rc # tp & sensors init_dev_detect # network #insmod /system/vendor/modules/bcmdhd.ko #insmod /system/vendor/modules/bcm_btlpm.ko insmod /system/vendor/modules/usbnet.ko insmod /system/vendor/modules/asix.ko insmod /system/vendor/modules/qf9700.ko #insmod /system/vendor/modules/mcs7830.ko #insmod /system/vendor/modules/smsc95xx.ko insmod /system/vendor/modules/rtl8152.ko #insmod /system/vendor/modules/cdc_ether.ko # bluetooth MAC address programming #chown bluetooth net_bt_stack ro.bt.bdaddr_path #chown bluetooth net_bt_stack /system/etc/bluetooth #chown bluetooth net_bt_stack /data/misc/bluetooth #setprop ro.bt.bdaddr_path "/data/misc/bluetooth/bdaddr" ## bluetooth ## UART device #chmod 0660 /dev/ttyS1 #chown bluetooth net_bt_stack /dev/ttyS1 # ## power up/down interface #chmod 0660 /sys/class/rfkill/rfkill0/state #chmod 0660 /sys/class/rfkill/rfkill0/type #chown bluetooth net_bt_stack /sys/class/rfkill/rfkill0/state #chown bluetooth net_bt_stack /sys/class/rfkill/rfkill0/type # # ## bluetooth LPM #chmod 0220 /proc/bluetooth/sleep/lpm #chmod 0220 /proc/bluetooth/sleep/btwrite #chown bluetooth net_bt_stack /proc/bluetooth/sleep/lpm #chown bluetooth net_bt_stack /proc/bluetooth/sleep/btwrite #write /proc/bluetooth/sleep/lpm 1 （使用的是android4.4.2的service：） # 1. realtek & eagle wifi service # 1.1 realtek & eagle wifi sta service service wpa_supplicant /system/bin/wpa_supplicant \ -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ -O/data/misc/wifi/sockets \ -e/data/misc/wifi/entropy.bin -g@android:wpa_wlan0 # we will start as root and wpa_supplicant will switch to user wifi # after setting up the capabilities required for WEXT # user wifi # group wifi inet keystore class main socket wpa_wlan0 dgram 660 wifi wifi disabled oneshot # 1.2 realtek & eagle wifi sta p2p concurrent service service p2p_supplicant /system/bin/wpa_supplicant \ -ip2p0 -Dnl80211 -c/data/misc/wifi/p2p_supplicant.conf \ -e/data/misc/wifi/entropy.bin -N \ -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ -O/data/misc/wifi/sockets \ -g@android:wpa_wlan0 class main socket wpa_wlan0 dgram 660 wifi wifi disabled oneshot ## broadcom wifi service ## 1 broadcom wifi sta service #service wpa_supplicant /system/bin/wpa_supplicant \ # -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ # -I/system/etc/wifi/wpa_supplicant_overlay.conf \ # -O/data/misc/wifi/sockets \ # -e/data/misc/wifi/entropy.bin -g@android:wpa_wlan0 # # we will start as root and wpa_supplicant will switch to user wifi # # after setting up the capabilities required for WEXT # # user wifi # # group wifi inet keystore # class main # socket wpa_wlan0 dgram 660 wifi wifi # disabled # oneshot # ## 2 broadcom wifi sta p2p concurrent service #service p2p_supplicant /system/bin/wpa_supplicant \ # -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ # -I/system/etc/wifi/wpa_supplicant_overlay.conf \ # -O/data/misc/wifi/sockets -N \ # -ip2p0 -Dnl80211 -c/data/misc/wifi/p2p_supplicant.conf \ # -I/system/etc/wifi/p2p_supplicant_overlay.conf \ # -puse_p2p_group_interface=1 -e/data/misc/wifi/entropy.bin \ # -g@android:wpa_wlan0 # # we will start as root and wpa_supplicant will switch to user wifi # # after setting up the capabilities required for WEXT # # user wifi # # group wifi inet keystore # class main # socket wpa_wlan0 dgram 660 wifi wifi # disabled # oneshot 4、（可不用修改：） R:\wyb\rtl8188eu_sina33m_sc3817\android\device\softwinner\astar-d7\ueventd.sun8i.rc 5、（可选修改：） R:\wyb\rtl8188eu_sina33m_sc3817\android\frameworks\base\packages\SettingsProvider\res\values\defaults.xml <integer name="def_screen_off_timeout">1800000</integer> <bool name="def_lockscreen_disabled">true</bool> R:\wyb\rtl8188eu_sina33m_sc3817\android\packages\apps\Camera2\src\com\android\camera\CameraActivity.java 6、（可选修改：） R:\wyb\rtl8188eu_sina33m_sc3817\lichee\linux-3.4\arch\arm\mach-sunxi\rf\bt_pm.c R:\wyb\rtl8188eu_sina33m_sc3817\lichee\linux-3.4\arch\arm\mach-sunxi\rf\wifi_pm.c struct wifi_pm_ops wifi_select_pm_ops; static char* wifi_mod[] = {" ", "ap6181", /* 1 - AP6181*/ "ap6210", /* 2 - AP6210*/ "rtl8188eu", /* 3 - RTL8188EU*/ "rtl8723au", /* 4 - RTL8723AU*/ "rtl8723bs", /* 5 - RTL8723BS*/ "esp8089", /* 6 - ESP8089*/ "ap6476", /* 7 - AP6476*/ "rtl8189es", /* 8 - rtl8189es*/ "ap6212", /* 9 - AP6212*/ "ap6330", /* 10- AP6330*/ "gb9663", /* 11- GB9663*/ }; static int __devinit wifi_pm_probe(struct platform_device *pdev) { struct wifi_pm_ops *ops = &wifi_select_pm_ops; switch (ops->module_sel.val) { case 1: /* AP6181 */ ap6xxx_gpio_init(); break; case 2: /* AP6210 */ ap6xxx_gpio_init(); break; case 3: /* RTL8188EU */ rtl8188eu_gpio_init(); break; case 4: /* RTL8723AU */ rtl8723au_gpio_init(); break; case 5: /* RTL8723BS */ rtl8723bs_gpio_init(); break; case 6: /* ESP8089 */ esp8089_gpio_init(); break; case 7: /* AP6476 */ ap6xxx_gpio_init(); break; case 8: /* rtl8189es */ rtl8189es_gpio_init(); break; case 9: /* AP6212 */ ap6xxx_gpio_init(); break; default: wifi_pm_msg("wrong sdio module select %d !\n", ops->module_sel.val); } awwifi_procfs_attach(); wifi_pm_msg("wifi gpio init is OK !!\n"); return 0; } 7、 R:\wyb\rtl8188eu_sina33m_sc3817\lichee\tools\pack\chips\sun8iw5p1\configs\d7\sys_config.fex [power_sply] dcdc1_vol = 3000 dcdc2_vol = 1100 dcdc3_vol = 1200 dcdc4_vol = 0 dcdc5_vol = 1500 aldo1_vol = 3300 aldo2_vol = 2500 aldo3_vol = 3000 dldo1_vol = 3300 dldo2_vol = 3300 dldo3_vol = 2800 ;gpio0_vol = 2800 ldoio0_vol = 2800 [jtag_para] jtag_enable = 0 [dram_para] dram_clk = 552 ;---------------------------------------------------------------------------------- ;uart configuration ;uart_used = uart x enable ;uart_type = 2:2 wire,4:4 wire,8:8 wire, full function ;---------------------------------------------------------------------------------- [uart0] uart_used = 1 uart_port = 0 uart_type = 2 uart_tx = port:PF02<3><1><default><default> uart_rx = port:PF04<3><1><default><default> ;---------------------------------------------------------------------------------- ;capacitor tp configuration ;ctp_twi_id : twi controller ID ;ctp_twi_addr : I2C slave address, 7bit ;ctp_screen_max_x/_y : resolution of touch panel ;ctp_revert_x/_y_flag : whether need to revert x/y ;ctp_exchange_x_y_flag: whether need to exchange the value of x and y ;ctp_int_port : port for tp's interrupt signal ;ctp_wakeup : port for wakeup tp ;---------------------------------------------------------------------------------- [ctp_para] ctp_used = 1 ctp_name = "gt82x" ctp_twi_id = 0 ctp_twi_addr = 0x5d ctp_screen_max_x = 1280 ctp_screen_max_y = 800 ctp_revert_x_flag = 1 ctp_revert_y_flag = 1 ctp_exchange_x_y_flag = 1 ctp_int_port = port:PL04<4><default><default><default> ctp_wakeup = port:PL03<1><default><default><1> ctp_power_ldo = ctp_power_ldo_vol = ctp_power_io = ;-------------------------------------------------------------------------------- ; CTP automatic detection configuration ;ctp_detect_used --- Whether startup automatic inspection function. 1:used,0:unused ;Module name postposition 1 said detection, 0 means no detection. ;-------------------------------------------------------------------------------- [ctp_list_para] ctp_det_used = 1 ft5x_ts = 1 gt82x = 1 gslX680 = 1 gslX680new = 0 gt9xx_ts = 1 gt9xxf_ts = 0 tu_ts = 0 gt818_ts = 1 zet622x = 1 aw5306_ts = 1 icn83xx_ts = 0 ;---------------------------------------------------------------------------------- ;lcd0 configuration ;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds; 4:dsi; 5:edp; 6:extend dsi ;lcd_x: lcd horizontal resolution ;lcd_y: lcd vertical resolution ;lcd_width: width of lcd in mm ;lcd_height: height of lcd in mm ;lcd_dclk_freq: in MHZ unit ;lcd_pwm_freq: in HZ unit ;lcd_pwm_pol: lcd backlight PWM polarity ;lcd_pwm_max_limit lcd backlight PWM max limit(<=255) ;lcd_hbp: hsync back porch ;lcd_ht: hsync total cycle ;lcd_vbp: vsync back porch ;lcd_vt: vysnc total cycle ;lcd_hspw: hsync plus width ;lcd_vspw: vysnc plus width ;lcd_lvds_if: 0:single link; 1:dual link ;lcd_lvds_colordepth: 0:8bit; 1:6bit ;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode ;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither ;lcd_io_phase: 0:noraml; 1:intert phase(0~3bit: vsync phase; 4~7bit:hsync phase; ; 8~11bit:dclk phase; 12~15bit:de phase) ;lcd_gamma_en lcd gamma correction enable ;lcd_bright_curve_en lcd bright curve correction enable ;lcd_cmap_en lcd color map function enable ;deu_mode 0:smoll lcd screen; 1:large lcd screen(larger than 10inch) ;lcdgamma4iep: Smart Backlight parameter, lcd gamma vale * 10; ; decrease it while lcd is not bright enough; increase while lcd is too bright ;smart_color 90:normal lcd screen 65:retina lcd screen(9.7inch) ;---------------------------------------------------------------------------------- [lcd0_para] lcd_used = 1 lcd_driver_name = "default_lcd" lcd_if = 3 lcd_x = 1280 lcd_y = 800 lcd_width = 150 lcd_height = 94 lcd_dclk_freq = 71 lcd_pwm_used = 1 lcd_pwm_ch = 0 lcd_pwm_freq = 50000 lcd_pwm_pol = 1 lcd_hbp = 20 lcd_ht = 1418 lcd_hspw = 10 lcd_vbp = 10 lcd_vt = 830 lcd_vspw = 5 lcd_lvds_if = 0 lcd_lvds_colordepth = 1 lcd_lvds_mode = 0 lcd_frm = 1 lcd_gamma_en = 0 lcd_bright_curve_en = 0 lcd_cmap_en = 0 deu_mode = 0 lcdgamma4iep = 22 smart_color = 90 lcd_bl_en = port:PD13<1><0><default><1> lcd_power = "axp22_dc1sw" lcdd0 = port:PD18<3><0><default><default> lcdd1 = port:PD19<3><0><default><default> lcdd2 = port:PD20<3><0><default><default> lcdd3 = port:PD21<3><0><default><default> lcdd4 = port:PD22<3><0><default><default> lcdd5 = port:PD23<3><0><default><default> lcdd6 = port:PD24<3><0><default><default> lcdd7 = port:PD25<3><0><default><default> lcdd8 = port:PD26<3><0><default><default> lcdd9 = port:PD27<3><0><default><default> ;---------------------------------------------------------------------------------- ;pwm config ;---------------------------------------------------------------------------------- [pwm0_para] pwm_used = 0 pwm_positive = port:PH00<2><0><default><default> [pwm1_para] pwm_used = 1 pwm_positive = port:PH01<2><0><default><default> ;---------------------------------------------------------------------------------- ;usb configuration ;usb_used: usb controller enable, 0-disable, 1-enable ;usb_port_type: usb mode: 0-device, 1-host, 2-otg ;usb_detect_type: usb hotplug detect mode, 0-none, 1-vbus/id detect, 2-id/dpdm detect ;usb_id_gpio: usb id detect IO ;usb_det_vbus_gpio: usb vbus detect IO, "axp_ctrl" for axp ;usb_drv_vbus_gpio: usb dirve vbus IO ;usb_restrict_gpio: usb current restrict IO ;usb_restric_flag: usb current restrict flag ;---------------------------------------------------------------------------------- [usbc0] usb_used = 1 usb_port_type = 2 usb_detect_type = 1 usb_id_gpio = port:PD10<0><1><default><default> usb_det_vbus_gpio = "axp_ctrl" usb_drv_vbus_gpio = port:power4<1><0><default><0> usb_restrict_gpio = usb_host_init_state = 0 usb_restric_flag = 0 usb_restric_voltage = 3550000 usb_restric_capacity= 5 usb_regulator_io = "nocare" usb_regulator_vol = 0 usb_regulator_id_vbus = "axp22_dcdc1" usb_regulator_id_vbus_vol = 3000000 [usbc1] usb_used = 1 usb_drv_vbus_gpio = port:PD12<1><0><default><0> usb_restrict_gpio = usb_host_init_state = 1 usb_restric_flag = 0 usb_regulator_io = "nocare" usb_regulator_vol = 0 usb_not_suspend = 0 ;-------------------------------------------------------------------------------- ;wifi/bt/fm/gps/nfc modules configuration ;module_num: ; 0- none ; 1- ap6181(wifi) ; 2- ap6210(wifi+bt) ; 3- rtl8188eu(wifi) ; 4- rtl8723au(wifi+bt) ; 5- rtl8723bs(wifi+bt) ; 6- esp8089(wifi) ; 7- ap6476(wifi+bt+fm+gps) ; 8- rtl8189es(wifi) ; 9- ap6212(wifi+bt+fm) ; 10- ap6330(wifi+bt+fm) ; 11- gb9663(wifi+bt+fm) ;module_power1: ""- bat, "axp_dldo1"- axp dldo1 ;module_power1_vol: power1 voltage, mv; not used for module_power1 is "" ;module_power2: ""- bat, "axp_dldo2"- axp dldo2 ;module_power2_vol: power2 voltage, mv; not used for module_power2 is "" ;module_power3: ""- bat, "axp_dldo2"- axp dldo2 ;module_power3_vol: power3 voltage, mv; not used for module_power3 is "" ;power_switch: module power switch io when bat supply ;chip_en: enable chip io ;lpo_use_apclk: ""- not use, "losc_out"- a23/33, "ac10032k1"、"ac10032k2"、"ac10032k3"- a80/a83 ;-------------------------------------------------------------------------------- [rf_para] module_num = 3 module_power1 = "" module_power1_vol = 3000000 module_power2 = "" module_power2_vol = 3000000 module_power3 = "" module_power3_vol = 3000000 power_switch = chip_en = lpo_use_apclk = "losc_out" ;-------------------------------------------------------------------------------- ;wifi configuration ;wifi_used: 0-not use, 1- use ;wifi_sdc_id: 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3 ;wifi_usbc_id: 0- USB0, 1- USB1, 2- USB2 ;wifi_usbc_type: 1- EHCI(speed 2.0), 2- OHCI(speed 1.0) ;wl_reg_on: wifi function enable io ;wl_host_wake: wifi device wake-up host ;wl_host_wake_invert: whether wl_host_wake use inverter between ap and module ; 0: not used, 1: used ;-------------------------------------------------------------------------------- [wifi_para] wifi_used = 1 wifi_sdc_id = 1 wifi_usbc_id = 1 wifi_usbc_type = 1 （请严重注意这里的选择，不然开不了机：） wifi_mod_sel = 3 wifi_power = "" wifi_power_ext1 = "" wifi_power_ext2 = "" ; 1 - ap6181 sdio wifi gpio config ;ap6xxx_wl_regon = port:PL06<1><default><default><0> ;ap6xxx_wl_host_wake = port:PL07<4><default><default><0> ;ap6xxx_lpo_use_apclk = 1 ; 2 - ap6210 sdio wifi gpio config ;ap6xxx_wl_regon = port:PL06<1><default><default><0> ;ap6xxx_wl_host_wake = port:PL07<4><default><default><0> ;ap6xxx_bt_regon = port:PL08<1><default><default><0> ;ap6xxx_bt_wake = port:PL10<1><default><default><0> ;ap6xxx_bt_host_wake = port:PL09<4><default><default><0> ;ap6xxx_lpo_use_apclk = 1 ; 3 - rtl8188eu usb wifi gpio conifg ; 4 - rtl8723au usb wifi + bt ; 5 - rtl8723bs sdio wifi + bt ;rtl8723bs_chip_en = port:PL11<1><default><default><0> ;rtl8723bs_wl_regon = port:PL06<1><default><default><0> ;rtl8723bs_wl_host_wake = port:PL07<4><default><default><0> ;rtl8723bs_bt_regon = port:PL08<1><default><default><0> ;rtl8723bs_bt_wake = port:PL10<1><default><default><0> ;rtl8723bs_bt_host_wake = port:PL09<4><default><default><0> ;rtl8723bs_lpo_use_apclk = 0 ; 6 - eagle sdio wifi ;esp_wl_chip_en = port:PL03<1><default><default><0> ;esp_wl_rst = port:PL02<1><default><default><0> ; 7 - ap6476 sdio wifi gpio config ;ap6xxx_wl_regon = port:PL06<1><default><default><0> ;ap6xxx_wl_host_wake = port:PL07<4><default><default><0> ;ap6xxx_bt_regon = port:PL08<1><default><default><0> ;ap6xxx_bt_wake = port:PL10<1><default><default><0> ;ap6xxx_bt_host_wake = port:PL09<4><default><default><0> ;ap6xxx_lpo_use_apclk = 1 ; 8 - rtl8189es sdio wifi gpio conifg ;rtl8189es_shdn = port:PL06<1><default><default><0> ;rtl8189es_host_wake = port:PL07<4><default><default><0> （关闭这里，不然开不了机：） ;usb_vbus_power_ctrl = port:PL11<1><default><default><1> ;usb_eth_power_ctrl = port:PL04<1><default><default><1> ;-------------------------------------------------------------------------------- ;bluetooth configuration ;bt_used: 0- no used, 1- used ;bt_uard_id: 0- uart0, 1- uart1, 2- uart2 ;bt_rst_n: bt function enable io ;bt_wake: host wake-up bluetooth device ;bt_wak_host: bt device wake-up host ;bt_wake_invert: whether bt_wake use inverter between ap and module ; 0: not used, 1: used ;bt_host_wake_invert: whether bt_host_wake use inverter between ap and module ; 0: not used, 1: used ;-------------------------------------------------------------------------------- [bt_para] （关闭：） bt_used = 0 bt_uart_id = 1 bt_rst_n = port:PL08<1><default><default><0> bt_wake = port:PL10<1><default><default><0> bt_host_wake = port:PL09<4><default><default><0> bt_wake_invert = 0 bt_host_wake_invert = 0 ls_int = port:PB07<1><default><default><0> pcm_ch = port:PB05<1><default><default><0> power_start = 3 pmu_temp_enable = 0 请严重注意：WIFI配置错误全志R16的系统启动不了： dldo2_vol = 3300 dldo3_vol = 2800 ldoio0_vol = 2800 find power_sply to end vbus exist no battery, limit to dc dram_para_set start dram_para_set end [ 5.079]DRAM: 512 MiB relocation Offset is: 15b0b000 workmode = 16 NAND_UbootProbe start NB1 : enter phy init NandHwInit: Start Nand Hardware initializing ..... uboot:physical version: 2 1f 20141023 1640 [NAND] channel cnt is 1 ndfc version: 1 ndfc dma mode: MBUS DMA Reset NDFC 0 NFC Randomizer start. NFC_ResetChip: 0x101, 0x100 0x10095 NFC_ResetChip: 0xff, ch: 0 [PHY_DBG] CH 0 Nand flash chip id is:0xf0 0xf0 0xf0 0xf0 0xf0 0xf0 nand id of two channel is not the same, set to 1 channel mode [SCAN_DBG] Nand flash chip id is:0xf0 0xf0 0xf0 0xf0 0xf0 0xf0 [SCAN_ERR] search nand physical architecture parameter failed! [ERR]NandHwInit: SCN_AnalyzeNandSystem() failed! NandHwInit: End Nand Hardware initializing ..... FAIL! NB1 : nand phy init fail NB1 : enter phy Exit nand release dma:0 NAND_UbootProbe end: 0xffffffff try nand fail [ 5.191][mmc]: mmc driver ver 2014-11-25 17:03:00 [ 5.196][mmc]: get sdc_phy_wipe fail. [ 5.200][mmc]: get sdc0 sdc_erase fail. [ 5.204][mmc]: get sdc_2xmode ok, val = 1 [ 5.208][mmc]: get sdc_ddrmode fail used = 0 [ 5.213][mmc]: get sdc_f_max fail,use default 50000000Hz [ 5.218][mmc]: get card_line ok, card_line = 4 [ 5.223][mmc]: undefined value 0 or kernel not use auto sample,use default dly [ 5.230][mmc]: SUNXI SD/MMC: 2 [ 5.243][mmc]: *Try SD card 2* [ 5.246][mmc]: mmc 2 cmd 8 err 100 [ 5.252][mmc]: mmc send if cond failed [ 5.256][mmc]: mmc 2 cmd 55 err 100 [ 5.261][mmc]: send app cmd failed [ 5.264][mmc]: *Try MMC card 2* [ 5.315][mmc]: CID 0x1501004d 0x34473146 0x42005603 0x5fe0cebb [ 5.320][mmc]: MMC ver 4.41 [ 5.323][mmc]: mmc clk 50000000 [ 5.327][mmc]: SD/MMC Card: 4bit, capacity: 3728MB [ 5.332][mmc]: boot0 capacity: 1000KB,boot1 capacity: 1000KB [ 5.337][mmc]: ***SD/MMC 2 init OK!!!*** [ 5.342][mmc]: erase_grp_size:0x400WrBlk * 0x200 = 0x80000 Byte [ 5.348][mmc]: secure_feature 0x15 [ 5.351][mmc]: secure_removal_type 0x0 read flash error out of usb burn from boot: not boot mode In: serial Out: serial Err: serial
rtl8188eu驱动
08-25
rtl8188eu驱动 海思平台验证完毕
rtl8188eu驱动程序
06-10
rtl8188eu驱动程序。适合所以rtl8188eu芯片。亲测可用
rtl8188eu_USB_linux.tar.gz
04-15
TP-LINK TL-WN725N V2 Linux 驱动安装
android ko 编译,如何把rtl8188EUS驱动编译生成ko模块并且下载到rk平台Android4.2.2上使用...
weixin_39695241的博客
05-26 537
下了rtl8188EUS_linux_v4.3.24_16705.20160509.tar.gz，看了里面的数据手册，发现有些看不懂，上网搜了一下，发现大部分博客都在扯淡。。。后来还是我把Makefile一句一句的看完才知道怎么做。具体应该怎么编译成我需要的模块呢？我的平台是rk3168。1、解压缩rtl8188EUS_linux_v4.3.24_16705.20160509.tar.gz，会看到...
realtek-rtl8188eu（0bda:8179芯片）无线网卡，kali系统安装驱动
qq_37735742的博客
04-09 2654
realtek-rtl8188eu（0bda:8179芯片）无线网卡，kali系统安装驱动
无线网卡（RTL8188EU）驱动编译、使用DHCP配置无线网络(1
热门推荐
jifengzhiling的博客
07-10 1万+
无线网卡（RTL8188EU）驱动编译、使用DHCP配置无线网络(1)http://www.openloongson.org/forum.php?mod=viewthread&amp;tid=220(出处: 龙芯俱乐部开源社区)1 驱动编译进入内核内核主界面下进入：（1）WIFI 设备支持配置及打开CONFIG_WIRELESS_EXT=y  CONFIG_WEXT_PRIV=yDevice Dr...
RTL8188EU驱动移植到ARM开发板：步骤与问题解决
"该资源提供了RTL8188ETV无线网卡芯片的驱动程序和工具在ARM开发板上的移植步骤，包括驱动的编译与内核集成，以及wpa_supplicant工具的使用。源码可以在百度网盘或GitHub上获取。" 在嵌入式系统中，将无线网卡驱动...
评论
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包

打赏作者

龙猫不是猫！

你的鼓励将是我创作的最大动力

¥1 ¥2 ¥4 ¥6 ¥10 ¥20
扫码支付：¥1
获取中
扫码支付

您的余额不足，请更换扫码支付或充值

打赏作者

实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值