如何安装和设置Schlage Connect Smart Lock

The Kwikset Kevo is one of the most popular smart locks on the market, but if you’re a stickler for keypads, the Schlage Connect is an option to consider. Here’s how to install and set up the Schlage Connect smart lock.

Kwikset Kevo是市场上最流行的智能锁之一，但是如果您是键盘操作者，可以考虑使用Schlage Connect 。 这是安装和设置Schlage Connect智能锁的方法。

The Connect isn’t an add-on to your existing deadbolt, but rather a full replacement. This can make the installation process a bit daunting for those who’ve never replaced a lock before. So before you get started, make sure that this is something you’re comfortable doing. If not, it may be wise to call a knowledgeable friend (or a professional locksmith) to help.

Connect不是您现有锁栓的附加组件，而是完整的替代品。 对于以前从未更换过锁的用户来说，这可能会使安装过程有些艰巨。 因此，在开始之前，请确保您感到满意。 如果没有，最好打电话给有知识的朋友(或专业的锁匠)来帮助。

This guide also assumes that you already have a deadbolt installed on your door. If you don’t, then you’ll need to drill a completely new hole in your door to install the Kevo (or any deadbolt for that matter) using one of these.

本指南还假定您的门上已经安装了锁舌。 如果您不这样做，则需要在其中的门上钻一个全新的Kong，以使用其中的一个安装Kevo(或与此有关的任何固定螺栓)。

Luckily, the Schlage Connect comes with everything that you’ll need, but you’ll need a couple of tools to put it all together: a screwdriver or power drill, and maybe a hammer. If you do decide to use a power drill, be extra careful not to over-tighten any screws.

幸运的是，Schlage Connect随附了您所需的一切，但您需要使用一些工具将它们组合在一起：螺丝刀或电钻，也许还有锤子。 如果您决定使用电钻，请格外小心，不要过度拧紧任何螺钉。

第一步：删除现有的固定螺栓 (Step One: Remove Your Existing Deadbolt)

Start by removing the deadbolt that’s currently installed on your door, which usually involves removing a couple of screws from the inside. My deadbolt is of the battery-powered keypad variety, so it’s a bit more complex to remove. If you just have a simple deadbolt, this process should be a lot easier for you.

首先，卸下门上当前安装的固定螺栓，通常需要从内部卸下几颗螺钉。 我的固定螺栓是电池供电的键盘种类，因此拆卸起来有点复杂。 如果您只有一个简单的固定螺栓，那么此过程对您来说应该会容易得多。

After those screws are removed, carefully take off the cover. You may have to slightly tap on it with a hammer to loosen it up if it doesn’t come off easily.

卸下这些螺钉后，请小心地取下盖子。 如果不容易脱落，则可能需要用锤子轻轻敲打使其松开。

There will be two more screws on the inside that you’ll need to remove. These connect the inside portion of the lock to the outside portion.

内部将需要卸下另外两个螺钉。 这些将锁的内部连接到外部。

Once those screws are removed, you can carefully pull apart the entire lock and remove it, starting with the interior section.

卸下这些螺钉后，您可以从内部部分开始小心地拉开整个锁并将其卸下。

From there, remove the outside portion.

从那里，除去外部。

Next, remove the two screws on the latch.

接下来，卸下闩锁上的两个螺钉。

Pull the latch out of the door.

将闩锁从门中拉出。

You now have a clean slate to install the Schlage Connect smart lock.

现在，您可以轻松安装Schlage Connect智能锁。

第二步：安装Schlage Connect (Step Two: Install the Schlage Connect)

The first step is to install the latch. Depending on the mortise of your door, there are different faceplates you can use, including a square faceplate, a rounded faceplate, and one without a faceplate at all. Take a look at your previous door latch and match it with the new one to see which one you need to use.

第一步是安装闩锁。 根据门的榫眼，可以使用不同的面板，包括方形面板，圆形面板和根本没有面板的面板。 查看您之前的门闩并将其与新的门闩匹配，以查看需要使用的门闩。

Insert the door latch into the door. Make sure that the middle hole in the door latch is centered within the door’s hole. If not, remove the latch, hold onto the deadbolt latch and rotate the mechanism 180 degrees to change the position of the middle hole. Re-insert the latch, making sure the “TOP” marking on the latch is facing upward.

将门闩插入门中。 确保门闩中的中间Kong在门Kong内居中。 如果不是，请卸下闩锁，握住固定螺栓闩锁，然后将机构旋转180度以更改中间Kong的位置。 重新插入闩锁，确保闩锁上的“ TOP”标记朝上。

Next, find the screws that have different threading (there will be four of them included, but you only need two).

接下来，找到具有不同螺纹的螺钉(将包括其中的四个，但您只需要两个)。

Use these two screws to secure the door latch onto the door.

使用这两个螺钉将门闩固定到门上。

Next, slide the keypad portion of the lock onto the outside part of the door.

接下来，将锁的键盘部分滑到门的外部。

Make sure that the cable feeds through the door hole and that the sticking out lines up and slides into the middle hole of the door latch.

确保电缆穿过门Kong，并且伸出的线对齐并滑入门闩的中间Kong。

Then take the support plate and place it on the inside part of the door, making sure that the side that reads “Against Door” is placed…well…against the door. When you do this, feed the cable through from the other side and line up the bolt holes.

然后拿起支撑板，将其放在门的内部，确保将标有“ Against Door”字样的一面放在门上……好……对着门。 执行此操作时，请从另一侧穿过电缆，并对准螺栓Kong。

Next, take the two long bolts included with the lock (the non-pointy ones) and screw the support plate into place.

接下来，取下锁随附的两个长螺栓(非尖头螺栓)并将支撑板拧入到位。

After that, grab the inside assembly and remove the battery cover.

之后，抓住内部组件并卸下电池盖。

At this point, you’ll also want to jot down the “Programming Code” and “User Codes” that are printed on the back of the assembly. You can change these in the future, but you’ll need them initially after installing the lock.

此时，您还需要记下印在组件背面的“编程代码”和“用户代码”。 您将来可以更改它们，但是安装锁后最初需要它们。

After you write those down, hold the assembly up to the lock and plug the cable into the back of it.

写下这些内容后，将组合件固定在锁上，然后将电缆插入其背面。

Route the cable into the grooves.

将电缆布线到凹槽中。

Slide the assembly over the support plate, making sure that the table sticking through lines up with the knob and push it all the way on.

将组件滑到支撑板上，确保桌子与旋钮成一直线，并将其完全推入。

Take the long black bolt and secure the inside assembly to the support plate.

取下黑色的长螺栓，并将内部组件固定到支撑板上。

Then take the really tiny screw and secure the upper portion.

然后拿起非常小的螺丝，并固定上部。

Once that’s complete, remove the battery tray by sliding it up and out of the assembly.

完成后，向上滑动电池托盘并将其从组件中取出，以将其卸下。

Insert the four AA batteries that came included with the lock.

插入锁随附的四节AA电池。

Slide the battery tray back into the assembly and connect the battery connector to the battery tray.

将电池托盘滑回组合件，然后将电池连接器连接到电池托盘。

After that, place the battery cover back on.

之后，重新盖上电池盖。

Next, it’s time to test out the lock and see if it works. Start by opening up the door (keeping it unlocked) and press on the “Schlage” button at the top of the keypad. The keypad should light up.

接下来，是时候测试一下锁，看看它是否有效了。 首先打开门(将门保持解锁状态)，然后按键盘顶部的“ Schlage”按钮。 键盘应亮起。

From there, enter in one of the user codes. If successful, the deadbolt will extend and retract. The lock should now be ready to go for manual usage.

从那里输入用户代码之一。 如果成功，锁舌将伸展和缩回。 现在应该准备好手动使用锁了。

第三步：将其连接到您的Smarthome Hub (Step Three: Connect It to Your Smarthome Hub)

While you can perform all sorts of functions on the lock itself (like adding new codes, changing codes, etc.), the big kicker for this lock is the ability to control and manage it from your smartphone by connecting it to a Z-Wave smarthome hub.

虽然您可以在锁本身上执行各种功能(例如添加新密码，更改密码等)，但此锁的最大作用是可以通过将其连接到Z-Wave从智能手机进行控制和管理智能家居中心。

How you do this is completely dependent on what type of smarthome hub you have, but the process should be mostly the same all around. In my case, I’m going to connect the lock to my Wink hub.

您如何执行此操作完全取决于您拥有哪种类型的智能家居集线器，但是整个过程应该大致相同。 就我而言，我将把锁连接到Wink集线器 。

To do this, you’ll first need to open up your smarthome hub app and navigate to where you add a device to the hub to put it in search mode.

为此，您首先需要打开smarthome集线器应用程序，然后导航到将设备添加到集线器的位置，以将其置于搜索模式。

Next, open your door, extend the deadbolt out so that it’s in the locked position, and then press the Schlage button followed by your programming code plus “0”. The orange dot will blink and after a few seconds the green check mark should light up, which indicates that connection was successful.

接下来，打开门，将固定栓伸出，使其处于锁定位置，然后按Schlage按钮，然后输入您的编程代码和“ 0”。 橙色点将闪烁，几秒钟后绿色复选标记应亮起，表明连接成功。

Once the lock has connected to the smarthome hub, you can begin controlling it from the hub’s app and do things like lock and unlock remotely, change user codes, and more.

一旦锁已连接到Smarthome集线器，您就可以开始从集线器的应用程序对其进行控制，并进行远程锁定和解锁，更改用户代码等操作。

Again, you can always manage the lock’s functionality using the lock itself without the need to connect it to a smarthome hub, but with the Schlage Connect, you’re essentially paying for the smarthome capabilities, so it would be beneficial to take advantage of it.

同样，您始终可以使用锁本身来管理锁的功能，而无需将其连接到智能家居集线器，但是通过Schlage Connect，您实质上是在为智能家居功能付费，因此，利用它会有所裨益。

翻译自: https://www.howtogeek.com/330039/how-to-install-and-set-up-the-schlage-connect-smart-lock/