经过前面的移植,u-boot已经有能力启动内核了,本文主要来看下如何通过之前移植的u-boot来启动内核。如果按照前面的文章完成了LTIB的编译,那么,Linux的内核应该就会出现rpm/BUILD/目录下,接下来,我们就开始移植这个3.0.35版本的内核到TQIMX6Q。
内核的编译
为了简化内核编译的过程,可以在内核目录下创建编译脚本,命名为build.sh,内容如下:
- #!/bin/sh
- export ARCH=arm
- export CROSS_COMPILE=/opt/freescale/usr/local/gcc-4.6.2-glibc-2.13-linaro-multilib-2011.12/fsl-linaro-toolchain/bin/arm-none-linux-gnueabi-
- make uImage -j8
为该脚本添加可执行权限:
- chmod a+x build.sh
- export PATH=$PATH:~/Projects/imx6/L3.0.35_4.1.0/ltib/rpm/BUILD/u-boot-2009.8/tools
- ./build.sh
内核启动尝试
内核编译完成后,uImage会出现在arch/arm/boot/目录下,将该镜像烧写到SD卡:
- sudo dd if=arch/arm/boot/uImage of=/dev/sdb bs=512 seek=2048
- sync
- sudo dd if=arch/arm/boot/uImage of=/dev/sdb bs=512 seek=2048 conv=fsync
- setenv bootargs_base 'setenv bootargs console=ttymxc0,115200'
- setenv bootargs_mmc 'setenv bootargs ${bootargs} root=/dev/mmcblk1p1 rootwait rw'
- setenv bootcmd_mmc 'run bootargs_base bootargs_mmc; mmc dev 1; mmc read ${loadaddr} 0x800 0x2000; bootm'
- setenv bootcmd 'run bootcmd_mmc'
- saveenv
- 第一条:bootargs_base,维持默认状态,作用是在bootargs中指定串口终端及波特率。
- 第二条:bootargs_mmc,是MMC方式启动内核使用的bootargs特有参数。
- 第三条:bootcmd_mmc,是MMC方式启动特有的命令组合。
- 第四条:bootcmd是内核启动命令。
- 第五条:保存env到SD存储介质。
完成之后执行命令:
- boot
内核的修改
通过上面的设置,u-boot已经可以引导内核启动了,但是,内核启动后仅打印了一部分log,猜测是内核中UART的GPIO管脚配置不正确,开始一段log能打印出来是因为u-boot阶段配置好了UART,而内核中又将这两个引脚配置为其它用途了。首先来解决串口log问题,打开文件arch/arm/mach-mx6/board-mx6q_sabresd.h并作如下修改:
- ... ...
- /* UART1 for debug */
- // MX6Q_PAD_CSI0_DAT10__UART1_TXD,
- MX6Q_PAD_SD3_DAT7__UART1_TXD,
- // MX6Q_PAD_CSI0_DAT11__UART1_RXD,
- MX6Q_PAD_SD3_DAT6__UART1_RXD,
- ... ...
- /* USDHC3 */
- MX6Q_PAD_SD3_CLK__USDHC3_CLK_50MHZ,
- MX6Q_PAD_SD3_CMD__USDHC3_CMD_50MHZ,
- MX6Q_PAD_SD3_DAT0__USDHC3_DAT0_50MHZ,
- MX6Q_PAD_SD3_DAT1__USDHC3_DAT1_50MHZ,
- MX6Q_PAD_SD3_DAT2__USDHC3_DAT2_50MHZ,
- MX6Q_PAD_SD3_DAT3__USDHC3_DAT3_50MHZ,
- // MX6Q_PAD_SD3_DAT4__USDHC3_DAT4_50MHZ,
- // MX6Q_PAD_SD3_DAT5__USDHC3_DAT5_50MHZ,
- // MX6Q_PAD_SD3_DAT6__USDHC3_DAT6_50MHZ,
- // MX6Q_PAD_SD3_DAT7__USDHC3_DAT7_50MHZ,
- MX6Q_PAD_NANDF_D0__GPIO_2_0, /* SD3_CD */
- MX6Q_PAD_NANDF_D1__GPIO_2_1, /* SD3_WP */
挂载文件系统
文件系统的构建方式都差不多,这里就不再自己构建了,直接使用LTIB编译时生成的文件系统。
将SD卡插ubunut上,对该SD卡进行分区:
- sudo fdisk /dev/sdb
Step1: 通过指令u切换到sectors模式。输入u后回车,fdisk会在sectors模式和cylinders模式间切换,这里切换到sectors模式。
Step2:通过d指令删除原来的分区。重复的输入d并回车,可以删除SD卡原有的分区,知道没有任何分区为止。
Step3:通过n指令新建分区。输入n并回车。
Step4:输入分区编号。这里输入数字1。
Step5:输入分区的起始位置。该位置是sectors为单位的,每个sector的大小为512B,这里偏移8M,给内核留下足够的存储空间,输入16384并回车。
Step6:输入分区的结束为止。直接使用默认值,即到达SD卡的末尾,故直接回车即可。
Step7:保存分区信息。输入指令w并回车。
这样就完成了SD卡的分区,接下来需要将该分区格式化为ext3或者ext4,指令如下:
- sudo mkfs.ext3 /dev/sdb1
- 或者
- sudo mkfs.ext4 /dev/sdb1
- sudo mount /dev/sdb1 /mnt
- sudo cp -a * /mnt
也可以重新拔插SD卡,将rootfs内的文件拷贝到ubunut挂载的分区。
如果rootfs是压缩包,则可以解压到SD卡分区,比如bzip的压缩包,可以如下处理:- sudo tar jxf rootfs.tar.bz2 -C /mnt
- sudo mv /mnt/rootfs/* /mnt
Step1:打开arch/arm/mach-mx6/board-mx6q_sabresd.h,作如下修改:
- /* USDHC2 */
- MX6Q_PAD_SD2_CLK__USDHC2_CLK,
- MX6Q_PAD_SD2_CMD__USDHC2_CMD,
- MX6Q_PAD_SD2_DAT0__USDHC2_DAT0,
- MX6Q_PAD_SD2_DAT1__USDHC2_DAT1,
- MX6Q_PAD_SD2_DAT2__USDHC2_DAT2,
- MX6Q_PAD_SD2_DAT3__USDHC2_DAT3,
- // MX6Q_PAD_NANDF_D4__USDHC2_DAT4,
- // MX6Q_PAD_NANDF_D5__USDHC2_DAT5,
- // MX6Q_PAD_NANDF_D6__USDHC2_DAT6,
- // MX6Q_PAD_NANDF_D7__USDHC2_DAT7,
- // MX6Q_PAD_NANDF_D2__GPIO_2_2, /* SD2_CD */
- MX6Q_PAD_GPIO_2__USDHC2_WP,
- // MX6Q_PAD_NANDF_D3__GPIO_2_3, /* SD2_WP */
- MX6Q_PAD_GPIO_4__USDHC2_CD,
- #define SABRESD_SD2_CD IMX_GPIO_NR(1, 4)
- #define SABRESD_SD2_WP IMX_GPIO_NR(1, 2)
按照以上步骤修改内核后重新编译并烧写到SD卡,然后使用SD卡启动开发板。
效果展示
按照上面的步骤修改后内核就可以正常启动了,下面是启动Log:
- U-Boot 2009.08-dirty ( 3月 23 2015 - 23:14:02)
- CPU: Freescale i.MX6 family TO1.2 at 792 MHz
- Thermal sensor with ratio = 174
- Temperature: 23 C, calibration data 0x54e4bb69
- mx6q pll1: 792MHz
- mx6q pll2: 528MHz
- mx6q pll3: 480MHz
- mx6q pll8: 50MHz
- ipg clock : 66000000Hz
- ipg per clock : 66000000Hz
- uart clock : 80000000Hz
- cspi clock : 60000000Hz
- ahb clock : 132000000Hz
- axi clock : 264000000Hz
- emi_slow clock: 132000000Hz
- ddr clock : 528000000Hz
- usdhc1 clock : 198000000Hz
- usdhc2 clock : 198000000Hz
- usdhc3 clock : 198000000Hz
- usdhc4 clock : 198000000Hz
- nfc clock : 24000000Hz
- Board: i.MX6Q-SABRESD: unknown-board Board: 0x63012 [POR ]
- Boot Device: SD
- I2C: ready
- DRAM: 1 GB
- MMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2,FSL_USDHC: 3
- In: serial
- Out: serial
- Err: serial
- Net: got MAC address from IIM: 00:00:00:00:00:00
- FEC0 [PRIME]
- Hit any key to stop autoboot: 0
- mmc1 is current device
- MMC read: dev # 1, block # 2048, count 8192 ... 8192 blocks read: OK
- ## Booting kernel from Legacy Image at 10800000 ...
- Image Name: Linux-3.0.35-2666-gbdde708-g3344
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 3866004 Bytes = 3.7 MB
- Load Address: 10008000
- Entry Point: 10008000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- OK
- Starting kernel ...
- Uncompressing Linux... done, booting the kernel.
- Linux version 3.0.35-2666-gbdde708-g334422e-dirty (lilianrong@ubuntu) (gcc version 4.6.2 20110630 (prerelease) (Freescale MAD -- Linaro 2011.07 -- Built at 2011/08/10 09:20) ) #5 SMP PREEMPT Wed Mar 25 19:29:24 CST 2015
- CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
- CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
- Machine: Freescale i.MX 6Quad/DualLite/Solo Sabre-SD Board
- Ignoring unrecognised tag 0x54410008
- Memory policy: ECC disabled, Data cache writealloc
- CPU identified as i.MX6Q, silicon rev 1.2
- PERCPU: Embedded 7 pages/cpu @8c008000 s5440 r8192 d15040 u32768
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 194560
- Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk1p1 rootwait rw
- PID hash table entries: 4096 (order: 2, 16384 bytes)
- Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
- Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
- Memory: 512MB 256MB = 768MB total
- Memory: 765764k/765764k available, 282812k reserved, 0K highmem
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- DMA : 0xf4600000 - 0xffe00000 ( 184 MB)
- vmalloc : 0xc0800000 - 0xf2000000 ( 792 MB)
- lowmem : 0x80000000 - 0xc0000000 (1024 MB)
- pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
- modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
- .init : 0x80008000 - 0x8003c000 ( 208 kB)
- .text : 0x8003c000 - 0x80a8f8f4 (10575 kB)
- .data : 0x80a90000 - 0x80af3e00 ( 400 kB)
- .bss : 0x80af3e24 - 0x80b41d4c ( 312 kB)
- SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- Preemptible hierarchical RCU implementation.
- NR_IRQS:624
- MXC GPIO hardware
- sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
- arm_max_freq=1GHz
- MXC_Early serial console at MMIO 0x2020000 (options '115200')
- bootconsole [ttymxc0] enabled
- Console: colour dummy device 80x30
- Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 512
- CPU: Testing write buffer coherency: ok
- hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
- CPU1: Booted secondary processor
- CPU2: Booted secondary processor
- CPU3: Booted secondary processor
- Brought up 4 CPUs
- SMP: Total of 4 processors activated (6324.22 BogoMIPS).
- print_constraints: dummy:
- NET: Registered protocol family 16
- print_constraints: vddpu: 725 <--> 1300 mV at 700 mV fast normal
- print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal
- print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
- print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
- print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
- print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
- hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
- hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
- hw-breakpoint: maximum watchpoint size is 4 bytes.
- L310 cache controller enabled
- l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B
- bio: create slab <bio-0> at 0
- mxs-dma mxs-dma-apbh: initialized
- print_constraints: SPKVDD: 4200 mV
- print_constraints: vmmc: 3300 mV
- SCSI subsystem initialized
- spi_imx imx6q-ecspi.0: probed
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- Freescale USB OTG Driver loaded, $Revision: 1.55 $
- mc_pfuze 1-0008: recv failed!:-5,80
- mc_pfuze: probe of 1-0008 failed with error -1
- imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
- imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
- mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 driver probed
- mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 dphy version is 0x3130302a
- MIPI CSI2 driver module loaded
- Advanced Linux Sound Architecture Driver Version 1.0.24.
- Bluetooth: Core ver 2.16
- NET: Registered protocol family 31
- Bluetooth: HCI device and connection manager initialized
- Bluetooth: HCI socket layer initialized
- Bluetooth: L2CAP socket layer initialized
- Bluetooth: SCO socket layer initialized
- cfg80211: Calling CRDA to update world regulatory domain
- max17135 2-0048: PMIC MAX17135 for eInk display
- i2c-core: driver [max17135] using legacy suspend method
- i2c-core: driver [max17135] using legacy resume method
- Switching to clocksource mxc_timer1
- NET: Registered protocol family 2
- IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
- TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
- TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
- TCP: Hash tables configured (established 131072 bind 65536)
- TCP reno registered
- UDP hash table entries: 512 (order: 2, 16384 bytes)
- UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
- NET: Registered protocol family 1
- RPC: Registered named UNIX socket transport module.
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- RPC: Registered tcp NFSv4.1 backchannel transport module.
- PMU: registered new PMU device of type 0
- Static Power Management for Freescale i.MX6
- wait mode is enabled for i.MX6
- cpaddr = c0880000 suspend_iram_base=c091c000
- PM driver module loaded
- IMX usb wakeup probe
- add wake up source irq 75
- IMX usb wakeup probe
- cpu regulator mode:ldo_enable
- i.MXC CPU frequency driver
- JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
- msgmni has been set to 1495
- alg: No test for stdrng (krng)
- io scheduler noop registered
- io scheduler deadline registered
- io scheduler cfq registered (default)
- mxc_mipi_dsi mxc_mipi_dsi: i.MX MIPI DSI driver probed
- MIPI DSI driver module loaded
- mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver ldb
- _regulator_get: get() with no identifier
- imx-ipuv3 imx-ipuv3.1: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
- Console: switching to colour frame buffer device 128x48
- mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver ldb
- mxc_sdc_fb mxc_sdc_fb.2: register mxc display driver lcd
- mxc_sdc_fb mxc_sdc_fb.3: register mxc display driver ldb
- mxc_sdc_fb mxc_sdc_fb.3: ipu1-di0 already in use
- mxc_sdc_fb: probe of mxc_sdc_fb.3 failed with error -16
- imx-sdma imx-sdma: loaded firmware 1.1
- imx-sdma imx-sdma: initialized
- Serial: IMX driver
- imx-uart.2: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX
- imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
- console [ttymxc0] enabled, bootconsole disabled
- console [ttymxc0] enabled, bootconsole disabled
- loop: module loaded
- No sata disk.
- m25p80 spi0.0: unrecognized JEDEC id ffffff
- GPMI NAND driver registered. (IMX)
- vcan: Virtual CAN interface driver
- CAN device driver interface
- flexcan netdevice driver
- FEC Ethernet Driver
- fec_enet_mii_bus: probed
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
- fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
- fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
- fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- add wake up source irq 72
- fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
- fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
- fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
- fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 1 port detected
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- ARC USBOTG Device Controller driver (1 August 2005)
- mousedev: PS/2 mouse device common for all mice
- input: gpio-keys as /devices/platform/gpio-keys/input/input0
- input: max11801_ts as /devices/platform/imx-i2c.1/i2c-1/1-0048/input/input1
- egalax_ts 1-0004: egalax_ts: failed to read firmware version
- egalax_ts: probe of 1-0004 failed with error -5
- egalax_ts 2-0004: egalax_ts: failed to read firmware version
- egalax_ts: probe of 2-0004 failed with error -5
- elan - Read Hello Packet Failed
- elan-touch: probe of 2-0010 failed with error -22
- i2c-core: driver [isl29023] using legacy suspend method
- i2c-core: driver [isl29023] using legacy resume method
- snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0
- i2c /dev entries driver
- Linux video capture interface: v2.00
- mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16
- mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17
- mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18
- mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video19
- mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video20
- mag3110 2-000e: check mag3110 chip ID
- mag3110 2-000e: read chip ID 0xfffffffb is not equal to 0xc4!
- mag3110: probe of 2-000e failed with error -22
- i2c-core: driver [mag3110] using legacy suspend method
- i2c-core: driver [mag3110] using legacy resume method
- mma8451 0-001c: read chip ID 0x1 is not equal to 0x1a or 0x2a!
- mma8451: probe of 0-001c failed with error -22
- imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
- Bluetooth: Virtual HCI driver ver 1.3
- Bluetooth: HCI UART driver ver 2.2
- Bluetooth: HCIATH3K protocol initialized
- Bluetooth: Generic Bluetooth USB driver ver 0.6
- usbcore: registered new interface driver btusb
- sdhci: Secure Digital Host Controller Interface driver
- sdhci: Copyright(c) Pierre Ossman
- mmc0: SDHCI controller on platform [sdhci-esdhc-imx.3] using DMA
- sdhci sdhci-esdhc-imx.1: no card-detect pin available!
- mmc1: SDHCI controller on platform [sdhci-esdhc-imx.1] using DMA
- mmc2: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA
- mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
- VPU initialized
- mxc_asrc registered
- Galcore version 4.6.9.6622
- Thermal calibration data is 0x54e4bb69
- Thermal sensor with ratio = 174
- Anatop Thermal registered as thermal_zone0
- anatop_thermal_probe: default cooling device is cpufreq!
- leds-gpio: probe of leds-gpio failed with error -16
- usbcore: registered new interface driver usbhid
- usbhid: USB HID core driver
- usbcore: registered new interface driver snd-usb-audio
- mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
- Cirrus Logic CS42888 ALSA SoC Codec Driver
- i2c-core: driver [cs42888] using legacy suspend method
- i2c-core: driver [cs42888] using legacy resume method
- imx-hdmi-soc-dai imx-hdmi-soc-dai.0: Failed: Load HDMI-video first.
- wm8962 0-001a: Failed to get supply 'DCVDD': -19
- wm8962 0-001a: Failed to request supplies: -19
- wm8962 0-001a: asoc: failed to probe CODEC wm8962.0-001a: -19
- asoc: failed to instantiate card wm8962-audio: -19
- mmc0: new high speed DDR MMC card at address 0001
- mmcblk0: mmc0:0001 008G92 7.28 GiB
- mmcblk0boot0: mmc0:0001 008G92 partition 1 4.00 MiB
- mmcblk0boot1: mmc0:0001 008G92 partition 2 4.00 MiB
- mmcblk0: p1 p2 p3 < p5 p6 p7 p8 > p4
- imx_3stack asoc driver
- mmcblk0boot1: unknown partition table
- Initialize HDMI-audio failed. Load HDMI-video first!
- ALSA device list:
- No soundcards found.
- NET: Registered protocol family 26
- TCP cubic registered
- NET: Registered protocol family 17
- can: controller area network core (rev 20090105 abi 8)
- NET: Registered protocol family 29
- can: raw protocol (rev 20090105)
- can: broadcast manager protocol (rev 20090105 t)
- Bluetooth: RFCOMM TTY layer initialized
- Bluetooth: RFCOMM socket layer initialized
- Bluetooth: RFCOMM ver 1.11
- Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- Bluetooth: BNEP filters: protocol multicast
- Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- lib80211: common routines for IEEE802.11 drivers
- VFP support v0.3:
- implementor 41 architecture 3 part 30 variant 9 rev 4
- mmcblk0boot0: unknown partition table
- Bus freq driver module loaded
- Bus freq driver Enabled
- mxc_dvfs_core_probe
- DVFS driver module loaded
- regulator_init_complete: SPKVDD: incomplete constraints, leaving on
- snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:46:38 UTC (2798)
- Waiting for root device /dev/mmcblk1p1...
- mmc1: new high speed SDHC card at address e624
- mmcblk1: mmc1:e624 SS08G 7.40 GiB
- mmcblk1: p1
- EXT3-fs: barriers not enabled
- kjournald starting. Commit interval 5 seconds
- EXT3-fs (mmcblk1p1): using internal journal
- EXT3-fs (mmcblk1p1): recovery complete
- EXT3-fs (mmcblk1p1): mounted filesystem with writeback data mode
- VFS: Mounted root (ext3 filesystem) on device 179:25.
- Freeing init memory: 208K
- starting pid 1401, tty '': '/etc/rc.d/rcS'
- Mounting /proc and /sys
- Starting the hotplug events dispatcher udevd
- udevd (1410): /proc/1410/oom_adj is deprecated, please use /proc/1410/oom_score_adj instead.
- Synthesizing initial hotplug events
- Setting the hostname to freescale
- Mounting filesystems
- cp: write error: No space left on device
- cp: write error: No space left on device
- cp: write error: No space left on device
- cp: write error: No space left on device
- cp: write error: No space left on device
- cp: write error: No space left on device
- mount: mounting usbfs on /proc/bus/usb failed: No such file or directory
- starting pid 3114, tty '': '/etc/rc.d/rc_gpu.S'
- starting pid 3120, tty '': '/etc/rc.d/rc_mxc.S'
- arm-none-linux-gnueabi-gcc (Freescale MAD -- Linaro 2011.07 -- Built at 2011/08/10 09:20) 4.6.2 20110630 (prerelease)
- root filesystem built on Sun, 15 Mar 2015 14:27:16 +0800
- Freescale Semiconductor, Inc.
- freescale login: root
- login[3122]: root login on 'ttymxc0'
- root@freescale ~$
- root@freescale ~$ cd /
- root@freescale /$ ls
- bin etc lost+found proc share unit_tests
- boot home mnt root sys usr
- dev lib opt sbin tmp var
- root@freescale /$
总结
基于Freescale官方维护的内核进行移植有非常详细的文档可以参考,而且还可以参考天嵌移植的代码,学习起来比较轻松,业余时间搞搞还是很不错的。以上有什么问题可以留言讨论。