VMIVME-7807/VME-7807RC的安装和通电指南

VMIVME-7807/VME-7807RC的安装和通电指南
板规格：
VMIVME-7807/VME-7807RC遵循6U板的VME物理规范。这些多功能板可以用作系统控制器或外围板，并与接受任何类型板的任何标准机箱兼容。

建议的安装和通电步骤：
遵循以下GE Fanuc嵌入式系统建议的步骤安装和通电VMIVME-7807/VME-7807RC：
PMC模块连接：
如果要使用PMC模块，请在安装板之前将其连接到VMIVME-7807/VME-7807RC。
有关配置和设置，请参阅PMC模块的产品手册。
确保适当的气流要求，测量的气流大于450LFM，尤其是在散热器的输出侧。

板插入：
将VMIVME-7807/VME-7807RC插入VME机箱系统控制器或外围插槽。
将板在支撑板导轨中正确对齐并定向。
将板顺滑向前，紧靠配合连接器。
使用弹出器手柄将板牢牢固定到位。

外围设备访问：
使用VMIACC-0586/ACC-0586RC或VMIACC-0590/ACC-0590RC后部转换模块（RTM）从前面板或后部I/O访问所有需要的外围设备。
前面板上有明显标记的连接器，附录A中提供了详细的引脚。

键盘和鼠标连接：
如果以前未配置系统，请连接键盘和鼠标。

CompactFlash磁盘设置：
VMIVME-7807/VME-7807RC具有一个位于板上的可选CompactFlash Disk。
有关CompactFlash Disk的设置详细信息，请参阅第3章。

外部驱动模块配置：
如果安装了外部驱动器模块，请使用BIOS设置程序配置驱动器类型。
有关正确的系统配置，请参阅附录B。

操作系统安装：
如果存在驱动器模块，请按照制造商的说明安装操作系统。

BIOS设置：
VMIVME-7807/VME-7807RC配备了板载BIOS设置程序，用于管理各种配置选项。这些信息存储在电池支持的非易失性存储芯片中，称为板的“CMOS配置”。CMOS配置从施加功率的那一刻起就影响硬件行为。有关VMIVME-7807/VME-7807RC BIOS设置程序的详细信息，请参阅附录B。
这些全面的步骤确保了VMIVME-7807/VME-7807RC板的顺利安装和配置过程，使用户能够有效地利用其全部功能。

Installation and Power-up Guide for VMIVME-7807/VME-7807RC

Board Specifications: The VMIVME-7807/VME-7807RC adhere to the VME physical specification for a 6U board. These versatile boards can serve as system controllers or peripheral boards and are compatible with any standard chassis accepting either type of board.

Recommended Installation and Power-up Steps: Follow these GE Fanuc Embedded Systems-recommended steps for the installation and power-up of VMIVME-7807/VME-7807RC:

1. PMC Module Connection:

   • If a PMC module is to be used, connect it to the VMIVME-7807/VME-7807RC before board installation.
   • Refer to the Product Manual for the PMC module for configuration and setup.
   • Ensure proper airflow requirements, with measured airflow greater than 450LFM, especially at the output side of the heatsink.

2. Board Insertion:

   • Insert the VMIVME-7807/VME-7807RC into a VME chassis system controller or peripheral slot.
   • Align and orient the board properly in the supporting board guides.
   • Slide the board smoothly forward against the mating connectors.
   • Use the ejector handles to firmly seat the board.

3. Peripheral Access:

   • Access all needed peripherals from the front panel or the rear I/O using VMIACC-0586/ACC-0586RC or VMIACC-0590/ACC-0590RC Rear Transition Modules (RTMs).
   • Clearly labeled connectors are available on the front panel, and detailed pinouts are provided in Appendix A.

4. Keyboard and Mouse Connection:

   • Connect a keyboard and mouse if the system has not been previously configured.

5. CompactFlash Disk Setup:

   • VMIVME-7807/VME-7807RC feature an optional CompactFlash Disk resident on the board.
   • Refer to Chapter 3 for setup details regarding the CompactFlash Disk.

6. External Drive Module Configuration:

   • If an external drive module is installed, use the BIOS Setup program to configure drive types.
   • Refer to Appendix B for proper system configuration.

7. Operating System Installation:

   • If a drive module is present, install the operating system following the manufacturer’s instructions.

BIOS Setup: The VMIVME-7807/VME-7807RC come equipped with an onboard BIOS Setup program that governs various configuration options. This information is stored in a battery-backed non-volatile memory chip known as the board’s ‘CMOS Configuration’. The CMOS configuration influences hardware behavior from the moment power is applied. Refer to Appendix B for details on the VMIVME-7807/VME-7807RC BIOS setup program.

These comprehensive steps ensure a smooth installation and configuration process for the VMIVME-7807/VME-7807RC boards, allowing users to harness their full capabilities effectively.