xy摇杆 ADC 串口显示模拟电压值的一些注意点

最新推荐文章于 2024-09-13 00:02:18 发布

C1336073449

最新推荐文章于 2024-09-13 00:02:18 发布

阅读量134

点赞数

文章标签：单片机 c++ 嵌入式硬件

本文链接：https://blog.csdn.net/C1336073449/article/details/130330307

版权

要用到printf打印串口时，要加以下代码：

#include "stdio.h"

int fputc(int ch,FILE *f)
{
    while((USART1->SR & 0X40 )== 0 );
	USART1->DR = (uint8_t)ch;
	return ch;

}

ADC多通道DMA，PA0--IN0,PA1--IN1

完整代码

/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "adc.h"
#include "dma.h"
#include "usart.h"
#include "gpio.h"

/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
#include "stdio.h"
#include "stdlib.h"
#include "string.h"
/* USER CODE END Includes */

/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */
uint16_t adc_value[2];
char uart_tx_buffer[50];

/* USER CODE END PTD */

/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD */

/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM */

/* USER CODE END PM */

/* Private variables ---------------------------------------------------------*/

/* USER CODE BEGIN PV */

/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
/* USER CODE BEGIN PFP */

/* USER CODE END PFP */

/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */
int fputc(int ch,FILE *f)
{
    while((USART1->SR & 0X40 )== 0 );
	USART1->DR = (uint8_t)ch;
	return ch;

}
/* USER CODE END 0 */

/**
  * @brief  The application entry point.
  * @retval int
  */
int main(void)
{
  /* USER CODE BEGIN 1 */

  /* USER CODE END 1 */

  /* MCU Configuration--------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* USER CODE BEGIN Init */

  /* USER CODE END Init */

  /* Configure the system clock */
  SystemClock_Config();

  /* USER CODE BEGIN SysInit */

  /* USER CODE END SysInit */

  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_DMA_Init();
  MX_ADC1_Init();
  MX_USART1_UART_Init();
  /* USER CODE BEGIN 2 */
  HAL_ADC_Start_DMA(&hadc1, (uint32_t*)&adc_value, 2);
  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
	  sprintf(uart_tx_buffer, "ADC1_IN0: %d, ADC1_IN1: %d\r\n", adc_value[0], adc_value[1]);
    HAL_UART_Transmit(&huart1, (uint8_t*)uart_tx_buffer, strlen(uart_tx_buffer), HAL_MAX_DELAY);
	  
    HAL_Delay(500);
	HAL_ADC_Start_DMA(&hadc1, (uint32_t*)&adc_value, 2);
	  
    /* USER CODE END WHILE */

    /* USER CODE BEGIN 3 */
  }
  /* USER CODE END 3 */
}

注意while1里面还要开启一次ADC采样，什么时候用hal_adc_stop呢?