本文首发于hifpga.com
XILINX的 serdes GT IP真的是够复杂的，生成的例子也是复杂，而且为了适配各种情况，代码里很多冗余的东西，发送部分比较简单 ，接收部分有点繁琐，我做了点注释，这里的只做的GTP的，GTX的自己看吧。
///
// ____ ____
// / /\/ /
// /___/ \ / Vendor: Xilinx
// \ \ \/ Version : 3.6
// \ \ Application : 7 Series FPGAs Transceivers Wizard
// / / Filename : gtwizard_0_gt_frame_check.v
// /___/ /\
// \ \ / \
// \___\/\___\
//
//
// Module gtwizard_0_GT_FRAME_CHECK
// Generated by Xilinx 7 Series FPGAs Transceivers Wizard
//
//
// (c) Copyright 2010-2012 Xilinx, Inc. All rights reserved.
//
// This file contains confidential and proprietary information
// of Xilinx, Inc. and is protected under U.S. and
// international copyright and other intellectual property
// laws.
//
// DISCLAIMER
// This disclaimer is not a license and does not grant any
// rights to the materials distributed herewith. Except as
// otherwise provided in a valid license issued to you by
// Xilinx, and to the maximum extent permitted by applicable
// law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// (2) Xilinx shall not be liable (whether in contract or tort,
// including negligence, or under any other theory of
// liability) for any loss or damage of any kind or nature
// related to, arising under or in connection with these
// materials, including for any direct, or any indirect,
// special, incidental, or consequential loss or damage
// (including loss of data, profits, goodwill, or any type of
// loss or damage suffered as a result of any action brought
// by a third party) even if such damage or loss was
// reasonably foreseeable or Xilinx had been advised of the
// possibility of the same.
//
// CRITICAL APPLICATIONS
// Xilinx products are not designed or intended to be fail-
// safe, or for use in any application requiring fail-safe
// performance, such as life-support or safety devices or
// systems, Class III medical devices, nuclear facilities,
// applications related to the deployment of airbags, or any
// other applications that could lead to death, personal
// injury, or severe property or environmental damage
// (individually and collectively, "Critical
// Applications"). Customer assumes the sole risk and
// liability of any use of Xilinx products in Critical
// Applications, subject only to applicable laws and
// regulations governing limitations on product liability.
//
// THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// PART OF THIS FILE AT ALL TIMES.
`timescale 1ns / 1ps
`define DLY #1
//***********************************Entity Declaration************************
(* DowngradeIPIdentifiedWarnings="yes" *)
module gtwizard_0_GT_FRAME_CHECK #
(
// parameter to set the number of words in the BRAM
parameter RX_DATA_WIDTH = 64,
parameter RXCTRL_WIDTH = 2,
parameter WORDS_IN_BRAM = 512,
parameter CHANBOND_SEQ_LEN = 1,
parameter COMMA_DOUBLE = 16'hf628,
parameter START_OF_PACKET_CHAR = 64'h00000000000000fb
)
(
// User Interface
input wire [(RX_DATA_WIDTH-1):0] RX_DATA_IN,
input wire [(RXCTRL_WIDTH-1):0] RXCTRL_IN,
output reg RXENPCOMMADET_OUT, // 未用，高电平有效信号，可实现字节边界对齐检测到plus COMMA模式时进行处理。
output reg RXENMCOMMADET_OUT, // 未用，高电平有效信号，可实现字节边界对齐检测到minus COMMA模式时进行处理。
output reg RX_ENCHAN_SYNC_OUT, // 未用，驱动mgt的enchansync端口进行通道绑定
input wire RX_CHANBOND_SEQ_IN, // 输入通道绑定序列，不绑定时为0
// Control Interface
input wire INC_IN, // 未用
output wire INC_OUT, // 非独立的收发测试时输出已开始进行COMMA检测，指示发送端地址递增
output wire PATTERN_MATCHB_OUT, // COMMA不匹配
input wire RESET_ON_ERROR_IN, // 通过将PATTERN_MATCHB_OUT输出给外部，由此产生出错后的复位
// Error Monitoring
output wire [7:0] ERROR_COUNT_OUT, // 错误数
// Track Data
output wire TRACK_DATA_OUT, // 指示接收到的数据是否符合预期
output wire RX_SLIDE, // 在对齐时要求GT滑动
// System Interface
input wire USER_CLK,
input wire SYSTEM_RESET
);
//***************************Internal Register Declarations********************
reg reset_on_error_in_r;
reg reset_on_error_in_r2;
(* ASYNC_REG = "TRUE" *) (* keep = "true" *)reg system_reset_r;
(* ASYNC_REG = "TRUE" *) (* keep = "true" *)reg system_reset_r2;
reg begin_r;
reg data_error_detected_r;
reg [8:0] error_count_r;
reg error_detected_r;
reg [9:0] read_counter_i;
reg [79:0] rom [0:511];
reg [(RX_DATA_WIDTH-1):0] rx_data_r;
reg [(RX_DATA_WIDTH-1):0] rx_data_r_track;
reg start_of_packet_detected_r;
reg track_data_r;
reg track_data_r2;
reg track_data_r3;
reg [79:0] rx_data_ram_r;
reg [(RX_DATA_WIDTH-1):0] rx_data_r2;
reg [(RX_DATA_WIDTH-1):0] rx_data_r3;
reg [(RX_DATA_WIDTH-1):0] rx_data_r4;
reg [(RX_DATA_WIDTH-1):0] rx_data_r5;
reg [(RX_DATA_WIDTH-1):0] rx_data_r6;
reg [(RXCTRL_WIDTH-1):0] rxctrl_r;
reg [(RXCTRL_WIDTH-1):0] rxctrl_r2;
reg [(RXCTRL_WIDTH-1):0] rxctrl_r3;
reg rx_chanbond_seq_r;
reg rx_chanbond_seq_r2;
reg rx_chanbond_seq_r3;
reg idle_slip_r;
reg slip_assert_r;
reg wait_state_r;
reg bit_align_r;
reg [6:0] wait_before_slip_r;
reg [6:0] wait_before_init_r;
reg [1:0] sel;
//*********************************Wire Declarations***************************
wire [(RX_DATA_WIDTH-1):0] bram_data_r;
wire error_detected_c;
wire next_begin_c;
wire next_data_error_detected_c;
wire next_track_data_c;
wire start_of_packet_detected_c;
wire chanbondseq_in_data;
wire input_to_chanbond_data_i;
wire input_to_chanbond_reg_i;
wire [(CHANBOND_SEQ_LEN-1):0] rx_chanbond_reg;
wire rxdata_or;
wire count_slip_complete_c;
wire next_idle_slip_c;
wire next_slip_assert_c;
wire wait_state_c;
wire [(RX_DATA_WIDTH-1):0] rx_data_aligned;
wire rx_data_has_start_char_c;
wire tied_to_ground_i;
wire [31:0] tied_to_ground_vec_i;
wire tied_to_vcc_i;
//*********************************Main Body of Code***************************
//_______________________ Static signal Assigments _______________________
assign tied_to_ground_i = 1'b0;
assign tied_to_ground_vec_i = 32'h0000;
assign tied_to_vcc_i = 1'b1;
//___________ synchronizing the async reset for ease of timing simulation ________
always@(posedge USER_CLK)
begin
system_reset_r <= `DLY SYSTEM_RESET;
system_reset_r2 <= `DLY system_reset_r;
end
always@(posedge USER_CLK)
begin
reset_on_error_in_r <= `DLY RESET_ON_ERROR_IN;
reset_on_error_in_r2 <= `DLY reset_on_error_in_r;
end
//______________________ Register RXDATA once to ease timing ______________
always @(posedge USER_CLK)
begin
rx_data_r <= `DLY RX_DATA_IN;
rx_data_r2 <= `DLY rx_data_r;
end
always @(posedge USER_CLK)
begin
rxctrl_r <= `DLY RXCTRL_IN;
end
//________________________________ State machine __________________________
// State registers
always @(posedge USER_CLK)
if(system_reset_r2)
{begin_r,track_data_r,data_error_detected_r} <= `DLY 3'b100;
else
begin
begin_r <= `DLY next_begin_c;
track_data_r <= `DLY next_track_data_c;
data_error_detected_r <= `DLY next_data_error_detected_c;
end
// Next state logic
assign next_begin_c = (begin_r && !start_of_packet_detected_r) // 产生启动请求信号，在该信号复位为高后且未收到已开始数据检测的指示时保持为高，或数据出错时
|| data_error_detected_r ;
assign next_track_data_c = (begin_r && start_of_packet_detected_r) // 产生检测数据跟踪请求，在启动为高后且收到开始检测到有效数据的指示时保持为高，或者已启动数据跟踪且未出错时
|| (track_data_r && !error_detected_r);
assign next_data_error_detected_c = (track_data_r && error_detected_r); // 已启动跟踪，且检测到了错误
assign start_of_packet_detected_c = rx_data_has_start_char_c; // 已开始检测到有效数据
always @(posedge USER_CLK)
start_of_packet_detected_r <= `DLY start_of_packet_detected_c;
// Registering for timing
always @(posedge USER_CLK)
track_data_r2 <= `DLY track_data_r;
always @(posedge USER_CLK)
track_data_r3 <= `DLY track_data_r2;
//______________________________ Capture incoming data ____________________
// 根据COMMA出现的位置将32b重新对齐
always @(posedge USER_CLK)
begin
if(system_reset_r2) rx_data_r3 <= 'h0;
else
begin
if(sel == 2'b01)
begin
rx_data_r3 <= `DLY {rx_data_r[(RX_DATA_WIDTH/4-1):0],rx_data_r2[(RX_DATA_WIDTH - 1):RX_DATA_WIDTH/4]};
end
else if(sel == 2'b10)
begin
rx_data_r3 <= `DLY {rx_data_r[(2*RX_DATA_WIDTH/4-1):0],rx_data_r2[(RX_DATA_WIDTH - 1):2*RX_DATA_WIDTH/4]};
end
else if(sel == 2'b11)
begin
rx_data_r3 <= `DLY {rx_data_r[(3*RX_DATA_WIDTH/4 - 1):0],rx_data_r2[(RX_DATA_WIDTH-1):3*RX_DATA_WIDTH/4]};
end
else rx_data_r3 <= `DLY rx_data_r2;
end
end
always @(posedge USER_CLK)
begin
if(system_reset_r2)
begin
rx_data_r4 <= `DLY 'h0;
rx_data_r5 <= `DLY 'h0;
rx_data_r6 <= `DLY 'h0;
rx_data_r_track <= `DLY 'h0;
end
else
begin
rx_data_r4 <= `DLY rx_data_r3;
rx_data_r5 <= `DLY rx_data_r4;
rx_data_r6 <= `DLY rx_data_r5;
rx_data_r_track <= `DLY rx_data_r6;
end
end
always @(posedge USER_CLK)
begin
if(system_reset_r2)
begin
rxctrl_r2 <= `DLY 'h0;
rxctrl_r3 <= `DLY 'h0;
end
else
begin
rxctrl_r2 <= `DLY rxctrl_r;
rxctrl_r3 <= `DLY rxctrl_r2;
end
end
assign rx_data_aligned = rx_data_r3;
//___________________________ Code for Channel bonding ____________________
// code to prevent checking of clock correction sequences for the start of packet char
always @(posedge USER_CLK)
begin
rx_chanbond_seq_r <= `DLY RX_CHANBOND_SEQ_IN;
rx_chanbond_seq_r2 <= `DLY rx_chanbond_seq_r;
rx_chanbond_seq_r3 <= `DLY rx_chanbond_seq_r2;
end
assign input_to_chanbond_reg_i = rx_chanbond_seq_r2; //一直为0
assign input_to_chanbond_data_i = tied_to_ground_i;
//______________ Code for Bit Slipping Logic______________
assign rxdata_or = |(rx_data_r|rx_data_r2|rx_data_r3); // 通道有收到数据
// State registers
always @(posedge USER_CLK)
if( (system_reset_r2 == 1'b1) | (wait_before_init_r[6] == 1'b0) | (rxdata_or == 1'b0) )
{idle_slip_r,slip_assert_r,wait_state_r} <= `DLY 3'b100;
else
begin
idle_slip_r <= `DLY next_idle_slip_c;
slip_assert_r <= `DLY next_slip_assert_c;
wait_state_r <= `DLY wait_state_c;
end
// Next state logic
assign next_idle_slip_c = (idle_slip_r & bit_align_r) | (wait_state_r & count_slip_complete_c); // slip操作空闲信号，当复为后且bit已对齐时，或者已完成执行滑窗后的等待
assign next_slip_assert_c = (idle_slip_r & !bit_align_r); // 继续执行slip,上一slip操作已完成，但bit仍未对齐
assign wait_state_c = (slip_assert_r) | (wait_state_r & !count_slip_complete_c); // slip请求已产生，但是等待操作还未完成，则持续等待
//_______ Counter for waiting clock cycles after RXSLIDE________
always @(posedge USER_CLK)
begin
if (!wait_state_r)
wait_before_slip_r <= `DLY 7'b000000;
else
wait_before_slip_r <= `DLY wait_before_slip_r + 1'b1; // slip操作等待计时器
end
//_______ Counter for waiting clock cycles before starting RXSLIDE operation________
//_______ Wait for 64 clock cycles to see if the RXDATA is already byte aligned. If not, start RXSLIDE operation
always @(posedge USER_CLK)
begin
if( (system_reset_r2 == 1'b1) | (rxdata_or == 1'b0) )
wait_before_init_r <= `DLY 7'b0000000;
else if (wait_before_init_r[6] == 1'b0) // 在启动接收前等待64clk
wait_before_init_r <= `DLY wait_before_init_r + 1'b1;
end
assign count_slip_complete_c = wait_before_slip_r[6];
always @(posedge USER_CLK)
begin
if( (system_reset_r2 == 1'b1) | (rxdata_or == 1'b0) ) begin
bit_align_r <= 1'b0;
end else begin
if( ({rx_data_r[23:0],rx_data_r2[31:24]} == START_OF_PACKET_CHAR) || ({rx_data_r[15:0],rx_data_r2[31:16]} == START_OF_PACKET_CHAR)
|| ({rx_data_r[7:0],rx_data_r2[31:8]} == START_OF_PACKET_CHAR) || (rx_data_r[31:0]== START_OF_PACKET_CHAR) )
begin
bit_align_r <= 1'b1; // 比较COMMA所有可能存在的4种情况以确定bit对齐
end
end
end
// Comma realignment logic might be needed. 4 levels of registering for RXDATA to meet timing
// In 4 Byte scenario, when align_comma_word=1, Comma can appear on any of the four bytes.
// { BYTE3 | BYTE2 | BYTE1 | BYTE0 } - Comma can appear on BYTE0/1/2/3
// If Comma appears on BYTE1/2/3, RX_DATA is realigned so that Comma appears on BYTE0 in rx_data_r_track
always @(posedge USER_CLK)
begin
if(reset_on_error_in_r2 || system_reset_r2) sel <= 2'b00;
else if (begin_r && !rx_chanbond_seq_r)
begin
// if Comma appears on BYTE3 ..
if((rx_data_r[(RX_DATA_WIDTH - 1) : 3*RX_DATA_WIDTH/4] == START_OF_PACKET_CHAR[7:0]) && rxctrl_r[3]) // rxctrl_r 指示COMMA出现的位置，并比较收的包头是否匹配
sel <= 2'b11;
// if Comma appears on BYTE2 ..
else if((rx_data_r[(3*RX_DATA_WIDTH/4 - 1):2*RX_DATA_WIDTH/4] == START_OF_PACKET_CHAR[7:0]) && rxctrl_r[2])
begin
sel <= 2'b10;
end
// if Comma appears on BYTE1 ..
else if((rx_data_r[(2*RX_DATA_WIDTH/4 - 1):RX_DATA_WIDTH/4] == START_OF_PACKET_CHAR[7:0]) && rxctrl_r[1])
begin
sel <= 2'b01;
end
// if Comma appears on BYTE0 ..
else if((rx_data_r[(RX_DATA_WIDTH/4 - 1):0] == START_OF_PACKET_CHAR[7:0]) && rxctrl_r[0])
begin
sel <= 2'b00;
end
end
end
//___________________________ Code for Channel bonding ____________________
// code to prevent checking of clock correction sequences for the start of packet char
genvar i;
generate
for (i=0;i<CHANBOND_SEQ_LEN ;i=i+1)
begin:register_chan_seq
if(i==0)
FD rx_chanbond_reg_0 ( .Q (rx_chanbond_reg[i]), .D (input_to_chanbond_reg_i), .C(USER_CLK));
else
FD rx_chanbond_reg_i ( .Q (rx_chanbond_reg[i]), .D (rx_chanbond_reg[i-1]), .C(USER_CLK));
end
endgenerate
assign chanbondseq_in_data = |rx_chanbond_reg || input_to_chanbond_data_i; // 未绑定始终为0
assign rx_data_has_start_char_c = (rx_data_aligned[7:0] == START_OF_PACKET_CHAR[7:0]) && !chanbondseq_in_data && (|rxctrl_r3); // 只要对齐后的数据有一byte匹配
//_____________________________ Assign output ports _______________________
//assign TRACK_DATA_OUT = track_data_r;
assign RX_SLIDE = slip_assert_r; // 输出slip信号
// Drive the enpcommaalign port of the gt for alignment
// Active-High signal that enables the byte boundary alignment process when the plus comma pattern is detected.
always @(posedge USER_CLK)
if(system_reset_r2) RXENPCOMMADET_OUT <= `DLY 1'b0;
else RXENPCOMMADET_OUT <= `DLY 1'b1;
// Drive the enmcommaalign port of the gt for alignment
// Active-High signal that enables the byte boundary alignment process when the minus comma pattern is detected.
always @(posedge USER_CLK)
if(system_reset_r2) RXENMCOMMADET_OUT <= `DLY 1'b0;
else RXENMCOMMADET_OUT <= `DLY 1'b1;
assign INC_OUT = start_of_packet_detected_c;
assign PATTERN_MATCHB_OUT = data_error_detected_r;
// Drive the enchansync port of the mgt for channel bonding
always @(posedge USER_CLK)
if(system_reset_r2) RX_ENCHAN_SYNC_OUT <= `DLY 1'b0;
else RX_ENCHAN_SYNC_OUT <= `DLY 1'b1;
//___________________________ Check incoming data for errors ______________
//An error is detected when data read for the BRAM does not match the incoming data
assign error_detected_c = track_data_r3 && (rx_data_r_track != bram_data_r); // 数据与ROM中不匹配
//We register the error_detected signal for use with the error counter logic
always @(posedge USER_CLK)
if(!track_data_r)
error_detected_r <= `DLY 1'b0;
else
error_detected_r <= `DLY error_detected_c;
//We count the total number of errors we detect. By keeping a count we make it less likely that we will miss
//errors we did not directly observe.
always @(posedge USER_CLK)
if(system_reset_r2)
error_count_r <= `DLY 9'd0;
else if(error_detected_r)
error_count_r <= `DLY error_count_r + 1;
//Here we connect the lower 8 bits of the count (the MSbit is used only to check when the counter reaches
//max value) to the module output
assign ERROR_COUNT_OUT = error_count_r[7:0];
localparam ST_LINK_DOWN = 1'b0;
localparam ST_LINK_UP = 1'b1;
reg sm_link = ST_LINK_DOWN;
reg [6:0] link_ctr = 7'd0;
always @(posedge USER_CLK) begin
if(!track_data_r)
sm_link <= ST_LINK_DOWN;
else
case (sm_link)
// The link is considered to be down when the link counter initially has a value less than 67. When the link is
// down, the counter is incremented on each cycle where all PRBS bits match, but reset whenever any PRBS mismatch
// occurs. When the link counter reaches 67, transition to the link up state.
ST_LINK_DOWN: begin
if (error_detected_r !== 1'b0) begin
link_ctr <= 7'd0;
end
else begin
if (link_ctr < 7'd67)
link_ctr <= link_ctr + 7'd1;
else
sm_link <= ST_LINK_UP;
end
end
// When the link is up, the link counter is decreased by 34 whenever any PRBS mismatch occurs, but is increased by
// only 1 on each cycle where all PRBS bits match, up to its saturation point of 67. If the link counter reaches
// 0 (including rollover protection), transition to the link down state.
ST_LINK_UP: begin
if (error_detected_r !== 1'b0) begin
if (link_ctr > 7'd33) begin
link_ctr <= link_ctr - 7'd34;
if (link_ctr == 7'd34)
sm_link <= ST_LINK_DOWN;
end
else begin
link_ctr <= 7'd0;
sm_link <= ST_LINK_DOWN;
end
end
else begin
if (link_ctr < 7'd67)
link_ctr <= link_ctr + 7'd1;
end
end
endcase
end
assign TRACK_DATA_OUT = sm_link;
//____________________________ Counter to read from BRAM __________________________
always @(posedge USER_CLK)
if(system_reset_r2 || (read_counter_i == (WORDS_IN_BRAM-1)))
begin
read_counter_i <= `DLY 10'd0;
end
else if (start_of_packet_detected_r && !track_data_r)
begin
read_counter_i <= `DLY 10'd0;
end
else
begin
read_counter_i <= `DLY read_counter_i + 10'd1;
end
//________________________________ BRAM Inference Logic _____________________________
//Array slice from dat file to compare against receive data
generate
if(RX_DATA_WIDTH==80)
begin : datapath_80
assign bram_data_r = rx_data_ram_r[(RX_DATA_WIDTH-1):0];
end
else
begin : datapath_16_20_32_40_64
assign bram_data_r = rx_data_ram_r[(16+RX_DATA_WIDTH-1):16];
end
endgenerate
`ifdef SIM
initial
begin
$readmemh("gt_rom_init_rx.dat",rom,0,511);
end
always @(posedge USER_CLK)
rx_data_ram_r <= `DLY rom[read_counter_i];
`else
always @(posedge USER_CLK)
rx_data_ram_r <= 'haa5555aa;//`DLY rom[read_counter_i];
`endif
endmodule
757
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
