3BHE037864R0106 UFC911 B106转换为十进制浮点以供使用

十进制浮点
1. 由于二进制浮点不是很友好，我们可以将其转换为十进制浮点以供使用。请注意，DVP-PLC中的小数点操作仍然是二进制浮点。
2. 十进制浮点由2个连续寄存器表示。编号较小的寄存器用于常数，而编号较大的寄存器用于指数。示例：将十进制浮点存储在寄存器（D1，D0）十进制浮点=[常数D0]×10[指数D1]常数D0=±1000 ~±9999指数D1=-41 ~+35由于100，D0中不存在常数100，表示为1000×10-1。小数点的浮动范围为±1175×10-41~±3402×10+35。
3. 十进制浮点可用于以下指令：D EBCD：将二进制浮点转换为十进制浮点D EBIN：将十进制浮点转换为二进制浮点
4. 零位标志（M1020）、进位标志（M1021）、进位标记（M1022）和浮点运算指令：零位标志：M1020=如果运算结果为“0”，则开启。借用标志：M1021=如果运算结果超过最小单位，则打开。进位标志：M1022=如果运算结果的绝对值超过使用范围，则为On。

索引寄存器是16位寄存器。ES/EC中有2个E、F点，SX中有8个E0~E3和F0~F3点，EH3/SV2/EC3-8K系列MPU中有16个E0~E7和F0~F7点。F0 E0 F0 E016位16位32位高字节低字节

1. E和F索引寄存器是16位数据寄存器。它们可以读写。

2. 如果你需要一个32位寄存器，你必须指定E。在这种情况下，F将被E覆盖，不能使用；否则，E中的内容可能会变得不正确。（我们建议您在PLC打开时使用MOVP指令将D中的内容重置为0。）

3. 指定32位索引寄存器时E和F的组合：（E0，F0）、（E1，F1）、（E2，F2）、。。。（E7，F7）

The I/O station in the cement grinding section controls the start stop and real-time monitoring of the current of each motor in the process line. Establish a DCS control station to automatically detect mill operating parameters, control the proportion of incoming materials, and control mill load. Dynamically display process flow charts, trend charts, ingredient control screens, and alarm diagrams. It is worth considering that the selection of on-site instruments can significantly reduce the cost of DCS. The TIS-Net-P600 control system used in the DCS system of the 600000 ton cement production line in Nenjiang, Heilongjiang is a fully open DCS system. The microcomputer batching system, pre added water balling system, on-site non-standard data service system, and QS-1 multi-element quality control system are also connected to TIS-Net-P600 to form a complete data network. Moreover, various industrial buses are supported, which can greatly reduce the hardware cost of the system. Users can also develop the system on this platform and choose their own hardware and software devices to ensure sufficient freedom and system openness. It is now the mainstream DCS system.

Its system structure and characteristics are as follows: ① System structure. TISNet-P consists of various types of hardware devices. The system is equipped with the following types of devices: 800 series control modules, 32 series and 33 series IO modules, distributed control cabinets, human-machine interface station HMI, and high-speed data networks. 800 series control unit XCU: With a high-performance microprocessor as the core, it performs process control operations The characteristics of the system structure. Distributed redundancy structure: XCU, network communication redundancy configuration, mutual backup.