所用的到语句:
GPIO_ResetBit (GPIOx,GPIO_Pin_x) 将GPIOx的x 引脚置低电平。
GPIO_SetBit (GPIOx,GPIO_Pin_x) 将GPIOx的x 引脚置高电平。
GPIO_ReadInputDataBit(GPIOx, GPIO_Pin_x) 读取GPIOx的x引脚的输入数据。
GPIO_ReadOutputDataBit(GPIOx, GPIO_Pin_x) 读取GPIOx的x引脚的输出数据。
主程序
#include "stm32f10x.h" // Device header
#include "Delay.h"
#include "LED.h"
#include "Key.h"
#include "Buzzer.h"
#include "LightSensor.h"
int main(void)
{
Buzzer_Init();
LightSensor_Init();
while(1)
{
if(LightSensor_Get()==1)
{
Buzzer_ON();
}
else
{
Buzzer_OFF ();
}
}
}
按键控制LED点亮
通过读取按键的值来控制LED亮灭。
#include "stm32f10x.h" // Device header
void LED_Init(void)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA,ENABLE);
GPIO_InitTypeDef GPIO_InitStruct;
GPIO_InitStruct.GPIO_Mode=GPIO_Mode_Out_PP;
GPIO_InitStruct.GPIO_Pin=GPIO_Pin_1 | GPIO_Pin_2;
GPIO_InitStruct.GPIO_Speed= GPIO_Speed_50MHz;
GPIO_Init(GPIOA,&GPIO_InitStruct);
GPIO_SetBits (GPIOA ,GPIO_Pin_1 | GPIO_Pin_2);
}
void LED1_ON(void)
{
GPIO_ResetBits (GPIOA ,GPIO_Pin_1);
}
void LED1_OFF(void)
{
GPIO_SetBits (GPIOA ,GPIO_Pin_1);
}
void LED1_Turn(void)
{
if(GPIO_ReadOutputDataBit(GPIOA,GPIO_Pin_1)==0)
{
GPIO_SetBits (GPIOA,GPIO_Pin_1);
}
else
{
GPIO_ResetBits (GPIOA,GPIO_Pin_1);
}
}
void LED2_ON(void)
{
GPIO_ResetBits (GPIOA ,GPIO_Pin_2);
}
void LED2_OFF(void)
{
GPIO_SetBits (GPIOA ,GPIO_Pin_2);
}
void LED2_Turn(void)
{
if(GPIO_ReadOutputDataBit(GPIOA,GPIO_Pin_2)==0)
{
GPIO_SetBits (GPIOA,GPIO_Pin_2);
}
else
{
GPIO_ResetBits (GPIOA,GPIO_Pin_2);
}
}
蜂鸣器
蜂鸣器接在PB12号口。
#include "stm32f10x.h" // Device header
void Buzzer_Init(void)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB,ENABLE);
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Mode=GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Pin=GPIO_Pin_12;
GPIO_InitStructure.GPIO_Speed= GPIO_Speed_50MHz;
GPIO_Init(GPIOB,&GPIO_InitStructure);
GPIO_SetBits (GPIOB ,GPIO_Pin_12);
}
void Buzzer_ON(void)
{
GPIO_ResetBits (GPIOB ,GPIO_Pin_12);
}
void Buzzer_OFF(void)
{
GPIO_SetBits (GPIOB ,GPIO_Pin_12);
}
void Buzzer_Turn(void)
{
if(GPIO_ReadOutputDataBit(GPIOB,GPIO_Pin_12)==0)
{
GPIO_SetBits (GPIOB,GPIO_Pin_12);
}
else
{
GPIO_ResetBits (GPIOB,GPIO_Pin_12);
}
}
光敏传感器
光敏传感器接在PB13号口,通过读取光敏传感器的值来控制蜂鸣器报警。
#include "stm32f10x.h" // Device header
void LightSensor_Init(void)
{
RCC_APB2PeriphClockCmd (RCC_APB2Periph_GPIOB,ENABLE);
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Mode=GPIO_Mode_IPU;
GPIO_InitStructure.GPIO_Pin=GPIO_Pin_13;
GPIO_InitStructure.GPIO_Speed= GPIO_Speed_50MHz;
GPIO_Init(GPIOB,&GPIO_InitStructure);
GPIO_SetBits (GPIOB ,GPIO_Pin_13);
}
uint8_t LightSensor_Get(void)
{
return GPIO_ReadInputDataBit(GPIOB ,GPIO_Pin_13);
}